* config/rs6000/altivec.md (build_vector_mask_for_load): Use MEM_P.
* config/rs6000/constraints.md (Q constraint): Use REG_P.
* config/rs6000/darwin.h (PREFERRED_RELOAD_CLASS): Use SYMBOL_REF_P.
* config/rs6000/freebsd64.h (ASM_OUTPUT_SPECIAL_POOL_ENTRY_P): Use
SYMBOL_REF_P, CONST_INT_P and CONST_DOUBLE_P.
* config/rs6000/linux64.h (ASM_OUTPUT_SPECIAL_POOL_ENTRY_P): Likewise.
* config/rs6000/predicates.md (altivec_register_operand, vint_operand,
vsx_register_operand, vsx_reg_sfsubreg_ok, vfloat_operand,
vlogical_operand, gpc_reg_operand, int_reg_operand,
int_reg_operand_not_pseudo): Use SUBREG_P and HARD_REGISTER_P.
(ca_operand, base_reg_operand, htm_spr_reg_operand, cc_reg_operand,
cc_reg_not_cr0_operand, input_operand): Use SUBREG_P.
(save_world_operation, restore_world_operation, lmw_operation,
stmw_operation): Use MEM_P and REG_P.
(tie_operand): Use MEM_P.
(vrsave_operation, crsave_operation): Use REG_P.
(mfcr_operation, mtcrf_operation): Use REG_P and CONST_INT_P.
(fpr_reg_operand): Use SUBREG_P and HARD_REGISTER_NUM_P.
(quad_int_reg_operand): Use HARD_REGISTER_NUM_P.
(call_operand): Use HARD_REGISTER_P.
(indexed_or_indirect_operand, altivec_indexed_or_indirect_operand):
Use CONST_INT_P.
(lwa_operand): Use SUBREG_P, REG_P and CONST_INT_P.
* config/rs6000/rs6000-p8swap.c (insn_is_load_p, insn_is_store_p,
quad_aligned_load_p, replace_swapped_aligned_store,
recombine_lvx_pattern, replace_swapped_aligned_load,
recombine_stvx_pattern): Use MEM_P.
(const_load_sequence_p, adjust_vperm, replace_swapped_load_constant):
Use MEM_P and SYMBOL_REF_P.
(rtx_is_swappable_p): Use REG_P and CONST_INT_P.
(insn_is_swappable_p): Use REG_P and MEM_P.
(insn_is_swap_p, (alignment_mask): Use CONST_INT_P.
* config/rs6000/rs6000-string.c (expand_block_clear, expand_block_move):
Use CONST_INT_P.
* config/rs6000/rs6000.c (rs6000_secondary_reload, rs6000_emit_cmove):
Use CONST_DOUBLE_P.
(rs6000_output_move_128bit): Use CONST_DOUBLE_P, CONST_INT_P and
CONST_WIDE_INT_P.
(rs6000_legitimize_address): Use CONST_DOUBLE_P, CONST_INT_P,
CONST_WIDE_INT_P, REG_P and SYMBOL_REF_P.
(rs6000_emit_move): Use CONST_DOUBLE_P, CONST_INT_P, HARD_REGISTER_P,
HARD_REGISTER_NUM_P, MEM_P, REG_P, SUBREG_P, SYMBOL_REF_P and
reg_or_subregno:
(output_toc): Use CONST_DOUBLE_P, CONST_INT_P and SYMBOL_REF_P.
(easy_altivec_constant, rs6000_legitimate_offset_address_p,
rs6000_mode_dependent_address, rs6000_expand_mtfsf_builtin,
rs6000_expand_set_fpscr_rn_builtin, rs6000_expand_set_fpscr_drn_builtin,
rs6000_expand_unop_builtin, INT_P, rs6000_generate_compare,
rs6000_machopic_legitimize_pic_address, rs6000_split_logical_inner,
rs6000_split_logical_di): Use CONST_INT_P.
(rs6000_legitimize_reload_address): Use CONST_INT_P, HARD_REGISTER_P,
REG_P and SYMBOL_REF_P.
(setup_incoming_varargs, rs6000_rtx_costs): Use CONST_INT_P and MEM_P.
(print_operand): Use CONST_INT_P, MEM_P and REG_P.
(virtual_stack_registers_memory_p, rs6000_legitimate_address_p,
mems_ok_for_quad_peep): Use CONST_INT_P and REG_P.
(rs6000_secondary_reload_memory): Use CONST_INT_P and SUBREG_P.
(small_data_operand, print_operand_address): Use CONST_INT_P and
SYMBOL_REF_P.
(split_stack_arg_pointer_used_p): Use HARD_REGISTER_P.
(rs6000_init_hard_regno_mode_ok, direct_move_p):
Use HARD_REGISTER_NUM_P.
(rs6000_secondary_reload_gpr): Use HARD_REGISTER_NUM_P and MEM_P.
(rs6000_secondary_reload_class): Use HARD_REGISTER_NUM_P, REG_P,
SUBREG_P and SYMBOL_REF_P.
(register_to_reg_type, rs6000_secondary_reload_inner): Use SUBREG_P
and HARD_REGISTER_NUM_P.
(rs6000_adjust_vec_address): Use HARD_REGISTER_NUM_P and
reg_or_subregno.
(rs6000_adjust_cost, find_mem_ref): Use MEM_P.
(macho_lo_sum_memory_operand, rs6000_eliminate_indexed_memrefs): Use
MEM_P and REG_P.
(legitimate_indirect_address_p, legitimate_lo_sum_address_p,
registers_ok_for_quad_peep, rs6000_output_function_epilogue,
find_addr_reg): Use REG_P.
(altivec_expand_vec_perm_const): Use REG_P and SUBREG_P.
(rs6000_emit_le_vsx_move): Use SUBREG_P.
(offsettable_ok_by_alignment, constant_pool_expr_p,
legitimate_small_data_p, rs6000_output_dwarf_dtprel,
rs6000_delegitimize_address, rs6000_const_not_ok_for_debug_p,
rs6000_cannot_force_const_mem, rs6000_output_addr_const_extra,
rs6000_assemble_integer, create_TOC_reference,
rs6000_emit_allocate_stack, rs6000_xcoff_encode_section_info,
rs6000_call_aix, rs6000_call_aix): Use SYMBOL_REF_P.
(rs6000_split_vec_extract_var): Use reg_or_subregno.
* config/rs6000/rtems.h (ASM_OUTPUT_SPECIAL_POOL_ENTRY_P): Use
CONST_DOUBLE_P, CONST_INT_P and SYMBOL_REF_P.
* config/rs6000/sysv4.h (ASM_OUTPUT_SPECIAL_POOL_ENTRY_P): Likewise.
* config/rs6000/xcoff.h (ASM_OUTPUT_SPECIAL_POOL_ENTRY_P): Likewise.
* config/rs6000/rs6000.h (RS6000_SYMBOL_REF_TLS_P): Use SYMBOL_REF_P.
(REGNO_OK_FOR_INDEX_P, REGNO_OK_FOR_BASE_P): Use HARD_REGISTER_NUM_P.
(INT_REG_OK_FOR_INDEX_P, INT_REG_OK_FOR_BASE_P): Use HARD_REGISTER_P.
(CONSTANT_ADDRESS_P): Use CONST_INT_P and SYMBOL_REF_P.
* config/rs6000/rs6000.md (define_expands strlensi, mod<mode>3
and cbranch<mode>4): Use CONST_INT_P.
(multiple define_splits): Use REG_P and SUBREG_P.
(define_expands call, call_value): Use MEM_P.
(define_expands sibcall, sibcall_value): Use CONST_INT_P and MEM_P.
(define insn *mtcrfsi): Use CONST_INT_P and REG_P.
* config/rs6000/vsx.md (*vsx_le_perm_load_<mode>,
*vsx_le_perm_load_v8hi, *vsx_le_perm_load_v16qi): Use HARD_REGISTER_P
and HARD_REGISTER_NUM_P.
(multiple define_splits): Use HARD_REGISTER_NUM_P.
From-SVN: r268253
