# BSD 3-Clause License
#
# Copyright 2020 Lawrence T. Clark, Vinay Vashishtha, or Arizona State
# University
#
# Redistribution and use in source and binary forms, with or without
# modification, are permitted provided that the following conditions are met:
#
# 1. Redistributions of source code must retain the above copyright notice,
# this list of conditions and the following disclaimer.
#
# 2. Redistributions in binary form must reproduce the above copyright
# notice, this list of conditions and the following disclaimer in the
# documentation and/or other materials provided with the distribution.
#
# 3. Neither the name of the copyright holder nor the names of its
# contributors may be used to endorse or promote products derived from this
# software without specific prior written permission.
#
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
# AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
# IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
# ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
# LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
# CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
# SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
# INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
# CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
# ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
# POSSIBILITY OF SUCH DAMAGE.
VERSION 5.8 ;
BUSBITCHARS "[]" ;
DIVIDERCHAR "/" ;
CLEARANCEMEASURE EUCLIDEAN ;
UNITS
DATABASE MICRONS 4000 ;
END UNITS
MANUFACTURINGGRID 0.001 ;
PROPERTYDEFINITIONS
LAYER LEF58_TYPE STRING ;
LAYER LEF58_PITCH STRING ;
LAYER LEF58_GAP STRING ;
LAYER LEF58_EOLKEEPOUT STRING ;
LAYER LEF58_SPACING STRING ;
LAYER LEF58_CORNERSPACING STRING ;
LAYER LEF58_WIDTHTABLE STRING ;
LAYER LEF58_CUTCLASS STRING ;
LAYER LEF58_SPACINGTABLE STRING ;
LAYER LEF58_ENCLOSURE STRING ;
LAYER LEF58_RIGHTWAYONGRIDONLY STRING ;
LAYER LEF58_RECTONLY STRING ;
END PROPERTYDEFINITIONS
LAYER OVERLAP
TYPE OVERLAP ;
END OVERLAP
LAYER nwell
TYPE MASTERSLICE ;
PROPERTY LEF58_TYPE "TYPE NWELL ;" ;
END nwell
LAYER pwell
TYPE MASTERSLICE ;
PROPERTY LEF58_TYPE "TYPE PWELL ;" ;
END pwell
LAYER Gate
TYPE MASTERSLICE ;
END Gate
LAYER Active
TYPE MASTERSLICE ;
END Active
LAYER V0
TYPE CUT ;
SPACING 0.072 ;
WIDTH 0.072 ;
END V0
LAYER M1
TYPE ROUTING ;
DIRECTION VERTICAL ;
PITCH 0.144 ;
WIDTH 0.072 ;
SPACING 0.072 ;
AREA 0.010656 ; # Min Area # This should ideally be 16x not 4x as each dimension is scaled up by 16
# we only allow landing on pins (set in router) so area should not matter
SPACING 0.072 RANGE 0.144 4.000 ; # This rule is redundant with the SPACING rule
PROPERTY LEF58_EOLKEEPOUT "EOLKEEPOUT 0.073 EXTENSION 0 0 0.124 ;" ; # Tip to Tip Spacing
PROPERTY LEF58_CORNERSPACING "CORNERSPACING CONVEXCORNER CORNERONLY 0.040 WIDTH 0.072 SPACING 0.072 ;" ;
OFFSET 0.0 ;
END M1
LAYER V1
TYPE CUT ;
SPACING 0.072 ; # unlike generate, this is really spacing, not center to center.
WIDTH 0.072 ;
END V1
LAYER M2
TYPE ROUTING ;
DIRECTION HORIZONTAL ;
WIDTH 0.072 ; # Min Width
SPACING 0.072 ; # Min Spacing
OFFSET -1.080 ;
# MINSIZE is set so that the minimum lenght of a segment is 36nm. At the proper rule size of
# 31nm, the lines can't be minimum space. This causes DRCs (like crazy). Same for M3
# MINSIZE 0.112 0.072 ;
# area is adjusted to match this (Nanoroute requires both AREA and MINSIZE)
AREA 0.010656 ;
MINSIZE 0.148 0.072 ;
PITCH 0.180 0.144 ;
# this enforces the correct routing tracks on M2 with wide M2 power rails
PROPERTY LEF58_PITCH "
PITCH 0.144 FIRSTLASTPITCH 0.180
;
" ;
# this checks for distance in any direction so is not correct
# 0.070 is to avoid conflicts with the adjacent lines. This should be caught by CORNERSPACING below
# SPACING 0.124 ENDOFLINE 0.1 WITHIN 0.070 ;
PROPERTY LEF58_SPACING
" SPACING 0.072 ENDOFLINE 0.1 WITHIN 0.08 ENDTOEND 0.124
PARALLELEDGE 0.100 WITHIN 0.08 ; " ;
PROPERTY LEF58_EOLKEEPOUT "
EOLKEEPOUT 0.1 EXTENSION 0.0 0.05 0.124 CORNERONLY ;
" ;
PROPERTY LEF58_CORNERSPACING "
CORNERSPACING CONVEXCORNER WIDTH 0.000 SPACING 0.080 ;
" ; # CORNER to CORNER SPACING Rule
# Originally no width table for M2 since it is the follow rails.
# They can be 1x or 2x (2x causes DRCs on SAV V1). However, this seems to allow a double width M2
# on vias, which violates. Thus, this is added. Note that wide power follow rails will violate.
PROPERTY LEF58_WIDTHTABLE "
WIDTHTABLE 0.072 0.36 0.648 0.936 1.224 1.512 ;
" ;
PROPERTY LEF58_RIGHTWAYONGRIDONLY "
RIGHTWAYONGRIDONLY ;
" ;
PROPERTY LEF58_RECTONLY "
RECTONLY ;
" ;
END M2
LAYER V2
TYPE CUT ;
SPACING 0.072 ;
WIDTH 0.072 ;
END V2
LAYER M3
TYPE ROUTING ;
DIRECTION VERTICAL ;
PITCH 0.144 ;
OFFSET 0.0 ;
WIDTH 0.072 ; # Min Width
SPACING 0.072 ; # Min Spacing
# MINSIZE is set so that the minimum lenght of a segment is 36nm. At the proper rule size of
# 31nm, the lines can't be minimum space. This causes DRCs (like crazy). Same for M2
# MINSIZE 0.112 0.072 ;
# area is adjusted to match this (Nanoroute requires both AREA and MINSIZE)
AREA 0.010656 ;
MINSIZE 0.148 0.072 ;
PROPERTY LEF58_SPACING
" SPACING 0.072 ENDOFLINE 0.1 WITHIN 0.05 ENDTOEND 0.124
PARALLELEDGE 0.100 WITHIN 0.08 ; " ;
PROPERTY LEF58_EOLKEEPOUT "
EOLKEEPOUT 0.1 EXTENSION 0.0 0.05 0.124 CORNERONLY ;
" ;
PROPERTY LEF58_CORNERSPACING "
CORNERSPACING CONVEXCORNER WIDTH 0.000 SPACING 0.080
;
" ; # CORNER to CORNER SPACING Rule
# to make the special route widths integer values of the tracks, i.e., 1, 5, 9, 13... min widths
# the widths should be calculated in the APR tool, since viaGen does not seem to respect these
PROPERTY LEF58_WIDTHTABLE
" WIDTHTABLE 0.072 0.36 0.648 0.936 1.224 1.512 ; " ;
PROPERTY LEF58_RIGHTWAYONGRIDONLY "
RIGHTWAYONGRIDONLY ;
" ;
PROPERTY LEF58_RECTONLY "
RECTONLY ;
" ;
END M3
LAYER V3
TYPE CUT ;
# SPACING 0.072 ;
# WIDTH 0.072 ;
# different format to allow long vias for SAV power connections
PROPERTY LEF58_CUTCLASS "
CUTCLASS V3 WIDTH 0.072 LENGTH 0.096 CUTS 1 ;
CUTCLASS V3_0p480 WIDTH 0.072 LENGTH 0.480 CUTS 4 ;
CUTCLASS V3_0p864 WIDTH 0.072 LENGTH 0.864 CUTS 8 ;
" ;
PROPERTY LEF58_SPACINGTABLE "
SPACINGTABLE
DEFAULT 0.136
CUTCLASS V3 V3_0p480 V3_0p864
V3 - - - - - -
V3_0p480 - - - - - -
V3_0p864 - - - - - -
;
" ;
# ENCLOSURE CUTCLASS V3 END 0.02 SIDE 0.0 ;
# covered below?
# ENCLOSURE CUTCLASS V3 END 0.02 SIDE 0.0 ;
PROPERTY LEF58_ENCLOSURE "
ENCLOSURE CUTCLASS V3 BELOW EOL 0.0 0.020 0.0 ;
ENCLOSURE CUTCLASS V3 ABOVE EOL 0.0 0.044 0.0 ;
ENCLOSURE CUTCLASS V3_0p480 END 0.0 SIDE 0.0 ;
ENCLOSURE CUTCLASS V3_0p864 END 0.0 SIDE 0.0 ;
" ;
END V3
LAYER M4
TYPE ROUTING ;
DIRECTION HORIZONTAL ;
PITCH 0.192 ;
WIDTH 0.096 ;
SPACING 0.096 ;
OFFSET 0.012 ;
AREA 0.032 ;
PROPERTY LEF58_SPACING "
SPACING 0.096 ENDOFLINE 0.1 WITHIN 0.160 ENDTOEND 0.160 ; " ;
PROPERTY LEF58_WIDTHTABLE
" WIDTHTABLE 0.096 0.480 0.864 1.248 1.632 ; " ;
PROPERTY LEF58_CORNERSPACING "
CORNERSPACING CONVEXCORNER CORNERONLY 0.192
WIDTH 0.000 SPACING 0.160 ;
" ;
PROPERTY LEF58_EOLKEEPOUT "
EOLKEEPOUT 0.1 EXTENSION 0.192 0.097 0.192 CORNERONLY ;
" ;
# spacing table is required for the rule that has wide metal requires a 72nm (288 scaled)
# spacing between wide and minimum metals
SPACINGTABLE
PARALLELRUNLENGTH 0.00
WIDTH 0.000 0.096
WIDTH 0.100 0.288 ;
PROPERTY LEF58_RIGHTWAYONGRIDONLY "
RIGHTWAYONGRIDONLY ;
" ;
PROPERTY LEF58_RECTONLY "
RECTONLY ;
" ;
END M4
LAYER V4
TYPE CUT ;
# spacing is 4 * 34 = 136
# SPACING 0.136 ;
# WIDTH 0.072 ;
# ENCLOSURE 0.044 0.0 ;
PROPERTY LEF58_CUTCLASS "
CUTCLASS Vx WIDTH 0.096 LENGTH 0.096 ;
CUTCLASS Vx_0p480 WIDTH 0.096 LENGTH 0.480 CUTS 4 ;
CUTCLASS Vx_0p864 WIDTH 0.096 LENGTH 0.864 CUTS 8 ;
CUTCLASS Vx_1p248 WIDTH 0.096 LENGTH 1.248 CUTS 12 ;
CUTCLASS Vx_1p632 WIDTH 0.096 LENGTH 1.632 CUTS 16 ;
" ;
PROPERTY LEF58_SPACINGTABLE "
SPACINGTABLE
DEFAULT 0.136
CUTCLASS Vx Vx_0p480 Vx_0p864 Vx_1p248 Vx_1p632
Vx - - - - - - - - - -
Vx_0p480 - - - - - - - - - -
Vx_0p864 - - - - - - - - - -
Vx_1p248 - - - - - - - - - -
Vx_1p632 - - - - - - - - - -
;
" ;
PROPERTY LEF58_ENCLOSURE "
ENCLOSURE CUTCLASS Vx 0.044 0.0 ;
ENCLOSURE CUTCLASS Vx EOL 0.0 0.044 0.044 ;
ENCLOSURE CUTCLASS Vx_0p480 END 0.00 SIDE 0.0 ;
ENCLOSURE CUTCLASS Vx_0p864 END 0.00 SIDE 0.0 ;
ENCLOSURE CUTCLASS Vx_1p248 END 0.00 SIDE 0.0 ;
ENCLOSURE CUTCLASS Vx_1p632 END 0.00 SIDE 0.0 ;
" ;
END V4
LAYER M5
TYPE ROUTING ;
DIRECTION VERTICAL ;
PITCH 0.192 ;
WIDTH 0.096 ;
SPACING 0.096 ;
OFFSET 0.0 ;
AREA 0.032 ;
PROPERTY LEF58_SPACING "
SPACING 0.096 ENDOFLINE 0.1 WITHIN 0.160 ENDTOEND 0.160 ; " ;
MINIMUMDENSITY 60 ;
MAXIMUMDENSITY 360 ;
DENSITYCHECKWINDOW 80 80 ;
DENSITYCHECKSTEP 40 ;
PROPERTY LEF58_WIDTHTABLE
" WIDTHTABLE 0.096 0.480 0.864 1.248 1.632 2.016 2.400 2.784 3.168 3.552 3.936 ; " ;
PROPERTY LEF58_CORNERSPACING "
CORNERSPACING CONVEXCORNER CORNERONLY 0.192
WIDTH 0.000 SPACING 0.160 ;
" ;
PROPERTY LEF58_EOLKEEPOUT "
EOLKEEPOUT 0.1 EXTENSION 0.192 0.097 0.192
CORNERONLY ;
" ;
SPACINGTABLE
PARALLELRUNLENGTH 0.00
WIDTH 0.000 0.096
WIDTH 0.100 0.288 ;
PROPERTY LEF58_RIGHTWAYONGRIDONLY "
RIGHTWAYONGRIDONLY ;
" ;
PROPERTY LEF58_RECTONLY "
RECTONLY ;
" ;
END M5
LAYER V5
TYPE CUT ;
PROPERTY LEF58_CUTCLASS "
CUTCLASS Vx WIDTH 0.096 LENGTH 0.128 ;
CUTCLASS Vx_0p480 WIDTH 0.096 LENGTH 0.640 CUTS 4 ;
CUTCLASS Vx_0p864 WIDTH 0.096 LENGTH 1.152 CUTS 8 ;
CUTCLASS Vx_1p248 WIDTH 0.096 LENGTH 1.664 CUTS 12 ;
CUTCLASS Vx_1p632 WIDTH 0.096 LENGTH 2.176 CUTS 16 ;
" ;
PROPERTY LEF58_SPACINGTABLE "
SPACINGTABLE
DEFAULT 0.136
CUTCLASS Vx Vx_0p480 Vx_0p864 Vx_1p248 Vx_1p632
Vx - - - - - - - - - -
Vx_0p480 - - - - - - - - - -
Vx_0p864 - - - - - - - - - -
Vx_1p248 - - - - - - - - - -
Vx_1p632 - - - - - - - - - -
;
" ;
# end refers to the end of the VIA! Thus, since it is rectangular the proper
# enclosure is on the side not the end...
# ENCLOSURE CUTCLASS Vx END 0.0 SIDE 0.044 ; But--this refers to top and bottom
# actually passing the rule is done by having the correct vias below.
PROPERTY LEF58_ENCLOSURE "
ENCLOSURE CUTCLASS Vx EOL 0.0 0.044 0.044 ;
ENCLOSURE CUTCLASS Vx_0p480 END 0.00 SIDE 0.0 ;
ENCLOSURE CUTCLASS Vx_0p864 END 0.00 SIDE 0.0 ;
ENCLOSURE CUTCLASS Vx_1p248 END 0.00 SIDE 0.0 ;
ENCLOSURE CUTCLASS Vx_1p632 END 0.00 SIDE 0.0 ;
" ;
# PROPERTY LEF58_ENCLOSURE "
# ENCLOSURE CUTCLASS Vx EOL 0.0 0.044 0.0 ;
# " ;
END V5
LAYER M6
TYPE ROUTING ;
DIRECTION HORIZONTAL ;
PITCH 0.256 ;
WIDTH 0.128 ;
SPACING 0.128 ;
AREA 0.035 ; # Areas still need tweaking
PROPERTY LEF58_SPACING
" SPACING 0.128 ENDOFLINE 0.15 WITHIN 0.160 ENDTOEND 0.160 ; " ;
PROPERTY LEF58_WIDTHTABLE
" WIDTHTABLE 0.128 0.640 1.152 1.664 2.176 ; " ;
PROPERTY LEF58_CORNERSPACING "
CORNERSPACING CONVEXCORNER CORNERONLY 0.192
WIDTH 0.000 SPACING 0.160 ;
" ;
PROPERTY LEF58_EOLKEEPOUT "
EOLKEEPOUT 0.2 EXTENSION 0.192 0.129 0.192 CORNERONLY ;
" ;
SPACINGTABLE
PARALLELRUNLENGTH 0.00
WIDTH 0.000 0.096
WIDTH 0.100 0.288 ;
PROPERTY LEF58_RIGHTWAYONGRIDONLY "
RIGHTWAYONGRIDONLY ;
" ;
PROPERTY LEF58_RECTONLY "
RECTONLY ;
" ;
END M6
LAYER V6
TYPE CUT ;
PROPERTY LEF58_CUTCLASS "
CUTCLASS Vx WIDTH 0.128 LENGTH 0.128 ;
CUTCLASS Vx_0p640 WIDTH 0.128 LENGTH 0.640 CUTS 4 ;
CUTCLASS Vx_1p152 WIDTH 0.128 LENGTH 1.152 CUTS 8 ;
CUTCLASS Vx_1p664 WIDTH 0.128 LENGTH 1.664 CUTS 12 ;
CUTCLASS Vx_2p176 WIDTH 0.128 LENGTH 2.176 CUTS 16 ;
" ;
PROPERTY LEF58_SPACINGTABLE "
SPACINGTABLE
DEFAULT 0.136
CUTCLASS Vx Vx_0p640 Vx_1p152 Vx_1p664 Vx_2p176
Vx - - - - - - - - - -
Vx_0p640 - - - - - - - - - -
Vx_1p152 - - - - - - - - - -
Vx_1p664 - - - - - - - - - -
Vx_2p176 - - - - - - - - - -
;
" ;
PROPERTY LEF58_ENCLOSURE "
ENCLOSURE CUTCLASS Vx 0.044 0.0 ;
ENCLOSURE CUTCLASS Vx EOL 0.0 0.044 0.044 ;
ENCLOSURE CUTCLASS Vx_0p640 END 0.00 SIDE 0.0 ;
ENCLOSURE CUTCLASS Vx_1p152 END 0.00 SIDE 0.0 ;
ENCLOSURE CUTCLASS Vx_1p664 END 0.00 SIDE 0.0 ;
ENCLOSURE CUTCLASS Vx_2p176 END 0.00 SIDE 0.0 ;
" ;
END V6
LAYER M7
TYPE ROUTING ;
DIRECTION VERTICAL ;
PITCH 0.256 ;
WIDTH 0.128 ;
SPACING 0.128 ;
AREA 0.035 ; # Areas still need tweaking
PROPERTY LEF58_SPACING
" SPACING 0.120 ENDOFLINE 0.15 WITHIN 0.160 ENDTOEND 0.160 ; " ;
PROPERTY LEF58_WIDTHTABLE
" WIDTHTABLE 0.128 0.640 1.152 1.664 2.176 ; " ;
TYPE ROUTING ;
DIRECTION VERTICAL ;
PROPERTY LEF58_CORNERSPACING "
CORNERSPACING CONVEXCORNER CORNERONLY 0.300
WIDTH 0.000 SPACING 0.160 ;
" ;
PROPERTY LEF58_EOLKEEPOUT "
EOLKEEPOUT 0.2 EXTENSION 0.192 0.129 0.192
CORNERONLY ;
" ;
SPACINGTABLE
PARALLELRUNLENGTH 0.00
WIDTH 0.000 0.096
WIDTH 0.100 0.288 ;
PROPERTY LEF58_RIGHTWAYONGRIDONLY "
RIGHTWAYONGRIDONLY ;
" ;
PROPERTY LEF58_RECTONLY "
RECTONLY ;
" ;
END M7
LAYER V7
TYPE CUT ;
SPACING 0.184 ;
WIDTH 0.128 ;
END V7
LAYER M8
TYPE ROUTING ;
DIRECTION HORIZONTAL ;
PITCH 0.32 0.32 ;
WIDTH 0.16 ;
AREA 30.08 ;
SPACINGTABLE
PARALLELRUNLENGTH 0 1.599 4.799 7.199
WIDTH 0 0.16 0.16 0.16 0.16
WIDTH 0.239 0.16 0.16 0.16 0.16
WIDTH 0.319 0.16 0.16 0.16 0.16
WIDTH 0.479 0.16 0.16 0.16 0.16
WIDTH 1.999 0.16 0.16 0.16 2
WIDTH 3.999 0.16 0.16 0.16 4 ;
MINIMUMCUT 2 WIDTH 7.22 WITHIN 6.82 FROMBELOW ;
MINIMUMCUT 2 WIDTH 7.22 WITHIN 6.82 FROMABOVE ;
MAXWIDTH 8 ;
MINSTEP 0.16 STEP ;
END M8
LAYER V8
TYPE CUT ;
SPACING 0.228 ;
WIDTH 0.16 ;
END V8
LAYER M9
TYPE ROUTING ;
DIRECTION VERTICAL ;
PITCH 0.32 0.32 ;
WIDTH 0.16 ;
AREA 30.08 ;
SPACINGTABLE
PARALLELRUNLENGTH 0 1.599 4.799 7.199
WIDTH 0 0.16 0.16 0.16 0.16
WIDTH 0.239 0.16 0.16 0.16 0.16
WIDTH 0.319 0.16 0.16 0.16 0.16
WIDTH 0.479 0.16 0.16 0.16 0.16
WIDTH 1.999 0.16 0.16 0.16 2
WIDTH 3.999 0.16 0.16 0.16 4 ;
MINIMUMCUT 2 WIDTH 7.22 WITHIN 6.82 FROMABOVE ;
MINSTEP 0.16 STEP ;
END M9
LAYER V9
TYPE CUT ;
SPACING 0.228 ;
WIDTH 0.16 ;
END V9
LAYER Pad
TYPE ROUTING ;
DIRECTION HORIZONTAL ;
PITCH 0.32 0.32 ;
WIDTH 0.16 ;
SPACINGTABLE
PARALLELRUNLENGTH 0 47.999
WIDTH 0 8 8
WIDTH 47.999 8 12 ;
MINIMUMCUT 1 WIDTH 0.16 WITHIN 6.82 FROMBELOW ;
MINIMUMCUT 1 WIDTH 1.44 WITHIN 6.82 FROMBELOW ;
MINIMUMCUT 2 WIDTH 7.22 WITHIN 6.82 FROMBELOW ;
MINIMUMDENSITY 80 ;
MAXIMUMDENSITY 320 ;
DENSITYCHECKWINDOW 400 400 ;
DENSITYCHECKSTEP 200 ;
END Pad
# vias
VIA VIA9Pad Default
LAYER M9 ;
RECT -0.2 -0.2 0.2 0.2 ;
LAYER Pad ;
RECT -0.2 -0.2 0.2 0.2 ;
LAYER V9 ;
RECT -0.2 -0.2 0.2 0.2 ;
END VIA9Pad
VIA VIA89 Default
LAYER M8 ;
RECT -0.08 -0.08 0.08 0.08 ;
LAYER M9 ;
RECT -0.08 -0.08 0.08 0.08 ;
LAYER V8 ;
RECT -0.08 -0.08 0.08 0.08 ;
END VIA89
VIA VIA78 Default
LAYER M7 ;
RECT -0.064 -0.108 0.064 0.108 ;
LAYER M8 ;
RECT -0.108 -0.080 0.108 0.080 ;
LAYER V7 ;
RECT -0.064 -0.064 0.064 0.064 ;
END VIA78
VIA VIA67 Default
LAYER M6 ;
RECT -0.108 -0.064 0.108 0.064 ;
LAYER M7 ;
RECT -0.064 -0.108 0.064 0.108 ;
LAYER V6 ;
RECT -0.064 -0.064 0.064 0.064 ;
END VIA67
VIA VIA56 Default
LAYER M5 ;
RECT -0.048 -0.108 0.048 0.108 ;
LAYER M6 ;
RECT -0.092 -0.064 0.092 0.064 ;
LAYER V5 ;
RECT -0.048 -0.064 0.048 0.064 ;
END VIA56
VIA VIA45 Default
LAYER M4 ;
RECT -0.092 -0.048 0.092 0.048 ;
LAYER M5 ;
RECT -0.048 -0.092 0.048 0.092 ;
LAYER V4 ;
RECT -0.048 -0.048 0.048 0.048 ;
END VIA45
VIA VIA34 Default
LAYER M3 ;
RECT -0.036 -0.068 0.036 0.068 ;
LAYER M4 ;
RECT -0.080 -0.048 0.080 0.048 ;
LAYER V3 ;
RECT -0.036 -0.048 0.036 0.048 ;
END VIA34
VIA VIA23 Default
LAYER M2 ;
RECT -0.056 -0.036 0.056 0.036 ;
LAYER M3 ;
RECT -0.036 -0.056 0.036 0.056 ;
LAYER V2 ;
RECT -0.036 -0.036 0.036 0.036 ;
END VIA23
VIA VIA12 Default
LAYER M1 ;
RECT -0.036 -0.044 0.036 0.044 ;
LAYER M2 ;
RECT -0.056 -0.036 0.056 0.036 ;
LAYER V1 ;
RECT -0.036 -0.036 0.036 0.036 ;
END VIA12
#################################
### VIARULE GENERATE DEFAULTS ###
#################################
VIARULE Pad_M9 GENERATE DEFAULT
LAYER M9 ;
ENCLOSURE 0 0.0 ;
LAYER Pad ;
ENCLOSURE 0.044 0 ;
LAYER V9 ;
RECT -0.064 -0.064 0.064 0.064 ;
SPACING 0.312 BY 0.312 ;
END Pad_M9
VIARULE M9_M8 GENERATE DEFAULT
LAYER M8 ;
ENCLOSURE 0.0 0 ;
LAYER M9 ;
ENCLOSURE 0 0.08 ;
LAYER V8 ;
RECT -0.08 -0.08 0.08 0.08 ;
SPACING 0.388 BY 0.388 ;
END M9_M8
VIARULE M8_M7 GENERATE DEFAULT
LAYER M7 ;
ENCLOSURE 0.0 0.0 ;
LAYER M8 ;
ENCLOSURE 0.044 0 ;
LAYER V7 ;
RECT -0.064 -0.064 0.064 0.064 ;
SPACING 0.312 BY 0.312 ;
END M8_M7
VIARULE M7_M6 GENERATE DEFAULT
LAYER M6 ;
ENCLOSURE 0.044 0 ;
LAYER M7 ;
ENCLOSURE 0 0.044 ;
LAYER V6 ;
RECT -0.064 -0.064 0.064 0.064 ;
SPACING 0.312 BY 0.312 ;
END M7_M6
VIARULE M6_M5 GENERATE DEFAULT
LAYER M5 ;
ENCLOSURE 0.044 0.0 ;
WIDTH 0.096 TO 0.096 ;
LAYER M6 ;
ENCLOSURE 0.044 0 ;
WIDTH 0.128 TO 0.128 ;
LAYER V5 ;
RECT -0.048 -0.064 0.048 0.064 ;
SPACING 0.232 BY 1.232 ; # purposely crazy to avoid dual cut on routing
END M6_M5
# to make the wide vias for power stripes (still SAV)
VIARULE M3_M2widePWR0p936 GENERATE
LAYER M2 ;
ENCLOSURE 0.0 0.0 ;
LAYER M3 ;
ENCLOSURE 0.0 0.0 ;
WIDTH 0.936 TO 0.936 ;
LAYER V2 ;
RECT -0.468 -0.036 0.468 0.036 ;
SPACING 1.108 BY 0.144 ;
END M3_M2widePWR0p936
# to make the wide vias for powers (still SAV)
VIARULE M4_M3widePWR0p864 GENERATE
LAYER M3 ;
ENCLOSURE 0.0 0.0 ;
WIDTH 0.934 TO 0.938 ;
LAYER M4 ;
ENCLOSURE 0.0 0.0 ;
WIDTH 0.862 TO 0.866 ;
LAYER V3 ;
RECT -0.036 -0.432 0.036 0.432 ;
SPACING 0.144 BY 1.108 ;
END M4_M3widePWR0p864
# to make the wide vias for powers (still SAV)
VIARULE M5_M4widePWR0p864 GENERATE
LAYER M4 ;
ENCLOSURE 0.0 0.0 ;
LAYER M5 ;
ENCLOSURE 0.0 0.0 ;
WIDTH 0.864 TO 0.864 ;
LAYER V4 ;
RECT -0.432 -0.048 0.432 0.048 ;
SPACING 2.128 BY 0.384 ;
END M5_M4widePWR0p864
# to make the wide vias for powers (still SAV)
VIARULE M6_M5widePWR1p152 GENERATE
LAYER M5 ;
ENCLOSURE 0.0 0.0 ;
LAYER M6 ;
ENCLOSURE 0.0 0.0 ;
WIDTH 1.152 TO 1.152 ;
LAYER V5 ;
RECT -0.048 -0.576 0.048 0.576 ;
SPACING 0.384 BY 1.528 ;
END M6_M5widePWR1p152
# to make the wide vias for powers (still SAV)
VIARULE M7_M6widePWR1p152 GENERATE
LAYER M6 ;
ENCLOSURE 0.0 0.0 ;
LAYER M7 ;
ENCLOSURE 0.0 0.0 ;
WIDTH 1.152 TO 1.152 ;
LAYER V6 ;
RECT -0.576 -0.064 0.576 0.064 ;
SPACING 2.128 BY 0.384 ;
END M7_M6widePWR1p152
VIARULE M2_M1 GENERATE DEFAULT
LAYER M1 ;
ENCLOSURE 0 0.0 ;
LAYER M2 ;
ENCLOSURE 0.008 0.0 ;
LAYER V1 ;
RECT -0.036 -0.036 0.036 0.036 ;
SPACING 0.144 BY 0.144 ;
END M2_M1
END LIBRARY