// ================================================================
// NVDLA Open Source Project
//
// Copyright(c) 2016 - 2017 NVIDIA Corporation. Licensed under the
// NVDLA Open Hardware License; Check "LICENSE" which comes with
// this distribution for more information.
// ================================================================
// File Name: nv_ram_rwsp_160x65_logic.v
`ifdef _SIMULATE_X_VH_
`else
`ifndef SYNTHESIS
`define tick_x_or_0 1'bx
`define tick_x_or_1 1'bx
`else
`define tick_x_or_0 1'b0
`define tick_x_or_1 1'b1
`endif
`endif
// verilint 549 off - async flop inferred
// verilint 446 off - reading from output port
// verilint 389 off - multiple clocks in module
// verilint 287 off - unconnected ports
// verilint 401 off - Clock is not an input to the module (we use gated clk)
// verilint 257 off - delays ignored by synth tools
// verilint 240 off - Unused input
// verilint 542 off - enabled flop inferred
// verilint 210 off - too few module ports
// verilint 280 off - delay in non-blocking assignment
// verilint 332 off - not all possible cases covered, but default case exists
// verilint 390 off - multiple resets in this module
// verilint 396 off - flop w/o async reset
// verilint 69 off - case without default, all cases covered
// verilint 34 off - unused macro
// verilint 528 off - variable set but not used
// verilint 530 off - flop inferred
// verilint 550 off - mux inferred
// verilint 113 off - multiple drivers to flop
// leda ELB072 off
`timescale 1ns / 10ps
`define TSMC_CM_UNIT_DELAY
`define TSMC_CM_NO_WARNING
module nv_ram_rwsp_160x65_logic (
SI,
SO_int_net,
ary_atpg_ctl,
ary_read_inh,
clk,
debug_mode,
di,
dout,
iddq_mode,
jtag_readonly_mode,
mbist_Di_w0,
mbist_Do_r0_int_net,
mbist_Ra_r0,
mbist_Wa_w0,
mbist_ce_r0,
mbist_en_sync,
mbist_ramaccess_rst_,
mbist_we_w0,
ore,
pwrbus_ram_pd,
ra,
re,
scan_en,
scan_ramtms,
shiftDR,
svop,
test_mode,
updateDR,
wa,
we,
write_inh
);
parameter FORCE_CONTENTION_ASSERTION_RESET_ACTIVE=1'b0;
// port list for submodule
input SI;
output SO_int_net;
input ary_atpg_ctl;
input ary_read_inh;
input clk;
input debug_mode;
input [64:0] di;
output [64:0] dout;
input iddq_mode;
input jtag_readonly_mode;
input [1:0] mbist_Di_w0;
output [64:0] mbist_Do_r0_int_net;
input [7:0] mbist_Ra_r0;
input [7:0] mbist_Wa_w0;
input mbist_ce_r0;
input mbist_en_sync;
input mbist_ramaccess_rst_;
input mbist_we_w0;
input ore;
input [31:0] pwrbus_ram_pd;
input [7:0] ra;
input re;
input scan_en;
input scan_ramtms;
input shiftDR;
input [7:0] svop;
input test_mode;
input updateDR;
input [7:0] wa;
input we;
input write_inh;
wire [7:0] sleep_en = pwrbus_ram_pd[7:0];
wire ret_en = pwrbus_ram_pd[8];
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_9 (.A(pwrbus_ram_pd[9]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_10 (.A(pwrbus_ram_pd[10]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_11 (.A(pwrbus_ram_pd[11]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_12 (.A(pwrbus_ram_pd[12]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_13 (.A(pwrbus_ram_pd[13]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_14 (.A(pwrbus_ram_pd[14]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_15 (.A(pwrbus_ram_pd[15]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_16 (.A(pwrbus_ram_pd[16]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_17 (.A(pwrbus_ram_pd[17]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_18 (.A(pwrbus_ram_pd[18]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_19 (.A(pwrbus_ram_pd[19]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_20 (.A(pwrbus_ram_pd[20]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_21 (.A(pwrbus_ram_pd[21]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_22 (.A(pwrbus_ram_pd[22]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_23 (.A(pwrbus_ram_pd[23]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_24 (.A(pwrbus_ram_pd[24]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_25 (.A(pwrbus_ram_pd[25]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_26 (.A(pwrbus_ram_pd[26]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_27 (.A(pwrbus_ram_pd[27]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_28 (.A(pwrbus_ram_pd[28]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_29 (.A(pwrbus_ram_pd[29]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_30 (.A(pwrbus_ram_pd[30]));
`endif
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_31 (.A(pwrbus_ram_pd[31]));
`endif
// DFT ATPG signals
wire ram_bypass = (scan_ramtms | ary_read_inh);
wire la_bist_clkw0;
wire la_bist_clkr0;
assign la_bist_clkr0 = la_bist_clkw0;
wire updateDR_sync;
sync2d_c_pp updateDR_synchronizer (.d(updateDR), .clk(la_bist_clkw0), .q(updateDR_sync), .clr_(mbist_ramaccess_rst_));
reg updateDR_sync_1p;
always @(posedge la_bist_clkr0 or negedge mbist_ramaccess_rst_) begin
if (!mbist_ramaccess_rst_)
updateDR_sync_1p <= 1'b0;
else
updateDR_sync_1p <= updateDR_sync;
end
wire debug_mode_sync;
wire dft_rst_gated_clk;
CKLNQD12PO4 CLK_GATE_clk (.Q(dft_rst_gated_clk), .CP(clk), .E(mbist_ramaccess_rst_), .TE(scan_en));
sync2d_c_pp debug_mode_synchronizer (.d(debug_mode), .clk(dft_rst_gated_clk), .q(debug_mode_sync), .clr_(mbist_ramaccess_rst_));
reg [7:0] Ra_array_reg_r0;
wire mbist_en_r;
// hardcode mbist_en_r stdcell flop to avoid x bash recoverability issue described in bug 1803479 comment #7
p_SDFCNQD1PO4 mbist_en_flop(.D(mbist_en_sync), .CP(dft_rst_gated_clk), .Q(mbist_en_r), .CDN(mbist_ramaccess_rst_));
// Declare the Data_reg signal beforehand
wire [64:0] Data_reg_r0;
// Data out bus for read port r0 for Output Mux
wire [64:0] r0_OutputMuxDataOut;
CKLNQD12PO4 UJ_la_bist_clkw0_gate (.Q(la_bist_clkw0), .CP(clk), .E(mbist_en_r | debug_mode_sync), .TE(scan_en));
// Write enable bus
wire we_0_0;
// Read enable bus
wire re_0_0;
// start of predeclareNvregSignals
wire ctx_ctrl_we;
wire clk_en_core = (re_0_0 | (|we_0_0));
wire gated_clk_core;
CKLNQD12PO4 UJ_clk_gate_core (.Q(gated_clk_core), .CP(clk), .E(clk_en_core), .TE(1'b0 | mbist_en_r | debug_mode_sync | scan_en));
wire shiftDR_en;
reg [64:0] pre_muxed_Di_w0;
wire [64:0] pre_muxed_Di_w0_A, pre_muxed_Di_w0_B;
wire pre_muxed_Di_w0_S;
assign pre_muxed_Di_w0_S = !debug_mode_sync;
assign pre_muxed_Di_w0_A = Data_reg_r0[64:0];
assign pre_muxed_Di_w0_B = {mbist_Di_w0[0], {32{mbist_Di_w0}}};
always @(pre_muxed_Di_w0_S or pre_muxed_Di_w0_A or pre_muxed_Di_w0_B)
case(pre_muxed_Di_w0_S) // synopsys infer_mux
1'b0 : pre_muxed_Di_w0 = pre_muxed_Di_w0_A;
1'b1 : pre_muxed_Di_w0 = pre_muxed_Di_w0_B;
default : pre_muxed_Di_w0 = {65{`tick_x_or_0}};
endcase
reg [64:0] muxed_Di_w0;
wire [64:0] muxed_Di_w0_A, muxed_Di_w0_B;
assign muxed_Di_w0_A = {di[64:0]};
assign muxed_Di_w0_B = pre_muxed_Di_w0;
wire muxed_Di_w0_S = debug_mode_sync | mbist_en_r;
always @(muxed_Di_w0_S or muxed_Di_w0_A or muxed_Di_w0_B)
case(muxed_Di_w0_S) // synopsys infer_mux
1'b0 : muxed_Di_w0 = muxed_Di_w0_A;
1'b1 : muxed_Di_w0 = muxed_Di_w0_B;
default : muxed_Di_w0 = {65{`tick_x_or_0}};
endcase
wire posedge_updateDR_sync = updateDR_sync & !updateDR_sync_1p;
wire access_en_w = posedge_updateDR_sync;
// ATPG logic: capture for non-data regs
wire dft_capdr_w = ary_atpg_ctl;
wire [7:0] pre_Wa_reg_w0;
reg [7:0] Wa_reg_w0;
wire [7:0] Wa_reg_w0_A, Wa_reg_w0_B;
wire Wa_reg_w0_S;
assign Wa_reg_w0_S = (!debug_mode_sync);
assign Wa_reg_w0_A = pre_Wa_reg_w0;
assign Wa_reg_w0_B = mbist_Wa_w0;
always @(Wa_reg_w0_S or Wa_reg_w0_A or Wa_reg_w0_B)
case(Wa_reg_w0_S) // synopsys infer_mux
1'b0 : Wa_reg_w0 = Wa_reg_w0_A;
1'b1 : Wa_reg_w0 = Wa_reg_w0_B;
default : Wa_reg_w0 = {8{`tick_x_or_0}};
endcase
reg [7:0] muxed_Wa_w0;
wire [7:0] muxed_Wa_w0_A, muxed_Wa_w0_B;
wire muxed_Wa_w0_S;
assign muxed_Wa_w0_S = debug_mode_sync | mbist_en_r;
assign muxed_Wa_w0_A = wa;
assign muxed_Wa_w0_B = Wa_reg_w0;
always @(muxed_Wa_w0_S or muxed_Wa_w0_A or muxed_Wa_w0_B)
case(muxed_Wa_w0_S) // synopsys infer_mux
1'b0 : muxed_Wa_w0 = muxed_Wa_w0_A;
1'b1 : muxed_Wa_w0 = muxed_Wa_w0_B;
default : muxed_Wa_w0 = {8{`tick_x_or_0}};
endcase
// testInst_*reg* for address and enable capture the signals going into RAM instance input
// 4.2.3.1 of bob's doc
wire Wa_reg_SO_w0;
wire [7:0]wadr_q;
assign pre_Wa_reg_w0 = wadr_q ;
wire we_reg_SO_w0;
wire re_reg_SO_r0;
wire we_reg_w0;
wire pre_we_w0;
assign pre_we_w0 = debug_mode_sync ?
({1{posedge_updateDR_sync}} & we_reg_w0) :
{1{(mbist_en_r & mbist_we_w0)}};
reg muxed_we_w0;
wire muxed_we_w0_A, muxed_we_w0_B;
wire muxed_we_w0_S;
assign muxed_we_w0_S = debug_mode_sync | mbist_en_r;
assign muxed_we_w0_A = we_0_0;
assign muxed_we_w0_B = pre_we_w0;
always @(muxed_we_w0_S or muxed_we_w0_A or muxed_we_w0_B)
case(muxed_we_w0_S) // synopsys infer_mux
1'b0 : muxed_we_w0 = muxed_we_w0_A;
1'b1 : muxed_we_w0 = muxed_we_w0_B;
default : muxed_we_w0 = {1{`tick_x_or_0}};
endcase
wire we_q;
assign we_reg_w0 = we_q ;
// ATPG logic: capture for non-data regs
wire dft_capdr_r = ary_atpg_ctl;
// ATPG logic: capture for non-data regs
wire [7:0] pre_Ra_reg_r0;
reg [7:0] Ra_reg_r0;
wire [7:0] Ra_reg_r0_A, Ra_reg_r0_B;
wire Ra_reg_r0_S;
assign Ra_reg_r0_S = (!debug_mode_sync);
assign Ra_reg_r0_A = pre_Ra_reg_r0;
assign Ra_reg_r0_B = mbist_Ra_r0;
always @(Ra_reg_r0_S or Ra_reg_r0_A or Ra_reg_r0_B)
case(Ra_reg_r0_S) // synopsys infer_mux
1'b0 : Ra_reg_r0 = Ra_reg_r0_A;
1'b1 : Ra_reg_r0 = Ra_reg_r0_B;
default : Ra_reg_r0 = {8{`tick_x_or_0}};
endcase
wire [7:0] D_Ra_reg_r0;
reg [7:0] muxed_Ra_r0;
wire [7:0] muxed_Ra_r0_A, muxed_Ra_r0_B;
wire muxed_Ra_r0_S;
assign muxed_Ra_r0_S = debug_mode_sync | mbist_en_r;
assign muxed_Ra_r0_A = ra;
assign muxed_Ra_r0_B = Ra_reg_r0;
always @(muxed_Ra_r0_S or muxed_Ra_r0_A or muxed_Ra_r0_B)
case(muxed_Ra_r0_S) // synopsys infer_mux
1'b0 : muxed_Ra_r0 = muxed_Ra_r0_A;
1'b1 : muxed_Ra_r0 = muxed_Ra_r0_B;
default : muxed_Ra_r0 = {8{`tick_x_or_0}};
endcase
assign D_Ra_reg_r0 = muxed_Ra_r0;
// verilint 110 off - Incompatible width
// verilint 630 off - Port connected to a NULL expression
// These are used for registering Ra in case of Latch arrays as well (i.e.
// used in functional path as well)
wire Ra_reg_SO_r0;
wire [7:0]radr_q;
assign pre_Ra_reg_r0 = radr_q ;
wire re_reg_r0;
wire access_en_r = posedge_updateDR_sync & re_reg_r0;
reg access_en_r_1p;
always @(posedge la_bist_clkw0 or negedge mbist_ramaccess_rst_)
if (!mbist_ramaccess_rst_)
access_en_r_1p <= 1'b0;
else
access_en_r_1p <= access_en_r;
wire pre_re_r0;
assign pre_re_r0 = (debug_mode_sync) ?
(posedge_updateDR_sync & re_reg_r0) :
(mbist_en_r & mbist_ce_r0);
reg muxed_re_r0;
wire muxed_re_r0_A, muxed_re_r0_B;
wire muxed_re_r0_S;
assign muxed_re_r0_S = debug_mode_sync | mbist_en_r;
assign muxed_re_r0_A = re;
assign muxed_re_r0_B = pre_re_r0;
always @(muxed_re_r0_S or muxed_re_r0_A or muxed_re_r0_B)
case(muxed_re_r0_S) // synopsys infer_mux
1'b0 : muxed_re_r0 = muxed_re_r0_A;
1'b1 : muxed_re_r0 = muxed_re_r0_B;
default : muxed_re_r0 = `tick_x_or_0;
endcase
wire re_q;
assign re_reg_r0 = re_q ;
// ------------------ START PIECE ----------------------------------
// Suffix : Piece RAMPDP_160X65_GL_M2_D2 (RamCell)
// Covers Addresses from 0 to 159 Addressrange: [7:0]
// Data Bit range: [64:0] (65 bits)
// Enables: 1 Enable range:
// Write Address bus
wire [7:0] wa_0_0;
assign wa_0_0 = muxed_Wa_w0[7:0];
// Write Data in bus
wire [64:0] Wdata;
assign Wdata = muxed_Di_w0[64:0];
assign we_0_0 = we;
// Read Address bus
wire [7:0] ra_0_0;
assign ra_0_0 = muxed_Ra_r0[7:0];
// Read DataOut bus
wire [64:0] dout_0_0;
assign re_0_0 = re;
// Doing Global setup for all ram pieces
// Following control signals are shared by all ram pieces
// Done global setup for ram pieces
//-----------------------------------------------------------
// Declare the Bist logic\n
// Declare some mbist control signals
//--------------------------------------------------
// Vlint doesn't understand paramaters?
// verilint 110 off - Incompatible width
//--------------------------------------------------
// Turn the verilint warnings on
// verilint 110 on - Incompatible width
// ----------------- begin Ram Cell RAMPDP_160X65_GL_M2_D2 -------------
// Write Port Stuff -----
// Declare the Write address bus
wire web = !(|muxed_we_w0) | write_inh;
// Read Port Stuff -----
// Declare the Read address bus
// Read enable
wire piece_re = muxed_re_r0 | ( scan_en & jtag_readonly_mode );
wire reb = !piece_re;
// Declare the ramOutData which connects to the ram directly
wire [64:0] ramDataOut;
assign dout_0_0[64:0] = ramDataOut[64:0];
RAMPDP_160X65_GL_M2_D2 ram_Inst_160X65 (
.CLK (gated_clk_core)
, .WADR_7 (wa_0_0[7])
, .WADR_6 (wa_0_0[6])
, .WADR_5 (wa_0_0[5])
, .WADR_4 (wa_0_0[4])
, .WADR_3 (wa_0_0[3])
, .WADR_2 (wa_0_0[2])
, .WADR_1 (wa_0_0[1])
, .WADR_0 (wa_0_0[0])
, .WD_64 (Wdata[64])
, .WD_63 (Wdata[63])
, .WD_62 (Wdata[62])
, .WD_61 (Wdata[61])
, .WD_60 (Wdata[60])
, .WD_59 (Wdata[59])
, .WD_58 (Wdata[58])
, .WD_57 (Wdata[57])
, .WD_56 (Wdata[56])
, .WD_55 (Wdata[55])
, .WD_54 (Wdata[54])
, .WD_53 (Wdata[53])
, .WD_52 (Wdata[52])
, .WD_51 (Wdata[51])
, .WD_50 (Wdata[50])
, .WD_49 (Wdata[49])
, .WD_48 (Wdata[48])
, .WD_47 (Wdata[47])
, .WD_46 (Wdata[46])
, .WD_45 (Wdata[45])
, .WD_44 (Wdata[44])
, .WD_43 (Wdata[43])
, .WD_42 (Wdata[42])
, .WD_41 (Wdata[41])
, .WD_40 (Wdata[40])
, .WD_39 (Wdata[39])
, .WD_38 (Wdata[38])
, .WD_37 (Wdata[37])
, .WD_36 (Wdata[36])
, .WD_35 (Wdata[35])
, .WD_34 (Wdata[34])
, .WD_33 (Wdata[33])
, .WD_32 (Wdata[32])
, .WD_31 (Wdata[31])
, .WD_30 (Wdata[30])
, .WD_29 (Wdata[29])
, .WD_28 (Wdata[28])
, .WD_27 (Wdata[27])
, .WD_26 (Wdata[26])
, .WD_25 (Wdata[25])
, .WD_24 (Wdata[24])
, .WD_23 (Wdata[23])
, .WD_22 (Wdata[22])
, .WD_21 (Wdata[21])
, .WD_20 (Wdata[20])
, .WD_19 (Wdata[19])
, .WD_18 (Wdata[18])
, .WD_17 (Wdata[17])
, .WD_16 (Wdata[16])
, .WD_15 (Wdata[15])
, .WD_14 (Wdata[14])
, .WD_13 (Wdata[13])
, .WD_12 (Wdata[12])
, .WD_11 (Wdata[11])
, .WD_10 (Wdata[10])
, .WD_9 (Wdata[9])
, .WD_8 (Wdata[8])
, .WD_7 (Wdata[7])
, .WD_6 (Wdata[6])
, .WD_5 (Wdata[5])
, .WD_4 (Wdata[4])
, .WD_3 (Wdata[3])
, .WD_2 (Wdata[2])
, .WD_1 (Wdata[1])
, .WD_0 (Wdata[0])
, .WE (!web)
, .RADR_7 (ra_0_0 [7] & !test_mode)
, .RADR_6 (ra_0_0 [6])
, .RADR_5 (ra_0_0 [5])
, .RADR_4 (ra_0_0 [4])
, .RADR_3 (ra_0_0 [3])
, .RADR_2 (ra_0_0 [2])
, .RADR_1 (ra_0_0 [1])
, .RADR_0 (ra_0_0 [0])
, .RE (!reb)
, .RD_64 (ramDataOut[64])
, .RD_63 (ramDataOut[63])
, .RD_62 (ramDataOut[62])
, .RD_61 (ramDataOut[61])
, .RD_60 (ramDataOut[60])
, .RD_59 (ramDataOut[59])
, .RD_58 (ramDataOut[58])
, .RD_57 (ramDataOut[57])
, .RD_56 (ramDataOut[56])
, .RD_55 (ramDataOut[55])
, .RD_54 (ramDataOut[54])
, .RD_53 (ramDataOut[53])
, .RD_52 (ramDataOut[52])
, .RD_51 (ramDataOut[51])
, .RD_50 (ramDataOut[50])
, .RD_49 (ramDataOut[49])
, .RD_48 (ramDataOut[48])
, .RD_47 (ramDataOut[47])
, .RD_46 (ramDataOut[46])
, .RD_45 (ramDataOut[45])
, .RD_44 (ramDataOut[44])
, .RD_43 (ramDataOut[43])
, .RD_42 (ramDataOut[42])
, .RD_41 (ramDataOut[41])
, .RD_40 (ramDataOut[40])
, .RD_39 (ramDataOut[39])
, .RD_38 (ramDataOut[38])
, .RD_37 (ramDataOut[37])
, .RD_36 (ramDataOut[36])
, .RD_35 (ramDataOut[35])
, .RD_34 (ramDataOut[34])
, .RD_33 (ramDataOut[33])
, .RD_32 (ramDataOut[32])
, .RD_31 (ramDataOut[31])
, .RD_30 (ramDataOut[30])
, .RD_29 (ramDataOut[29])
, .RD_28 (ramDataOut[28])
, .RD_27 (ramDataOut[27])
, .RD_26 (ramDataOut[26])
, .RD_25 (ramDataOut[25])
, .RD_24 (ramDataOut[24])
, .RD_23 (ramDataOut[23])
, .RD_22 (ramDataOut[22])
, .RD_21 (ramDataOut[21])
, .RD_20 (ramDataOut[20])
, .RD_19 (ramDataOut[19])
, .RD_18 (ramDataOut[18])
, .RD_17 (ramDataOut[17])
, .RD_16 (ramDataOut[16])
, .RD_15 (ramDataOut[15])
, .RD_14 (ramDataOut[14])
, .RD_13 (ramDataOut[13])
, .RD_12 (ramDataOut[12])
, .RD_11 (ramDataOut[11])
, .RD_10 (ramDataOut[10])
, .RD_9 (ramDataOut[9])
, .RD_8 (ramDataOut[8])
, .RD_7 (ramDataOut[7])
, .RD_6 (ramDataOut[6])
, .RD_5 (ramDataOut[5])
, .RD_4 (ramDataOut[4])
, .RD_3 (ramDataOut[3])
, .RD_2 (ramDataOut[2])
, .RD_1 (ramDataOut[1])
, .RD_0 (ramDataOut[0])
, .SVOP_0 (svop[0])
, .SVOP_1 (svop[1])
, .SVOP_2 (svop[2])
, .SVOP_3 (svop[3])
, .SVOP_4 (svop[4])
, .SVOP_5 (svop[5])
, .SVOP_6 (svop[6])
, .SVOP_7 (svop[7])
, .IDDQ (iddq_mode)
, .SLEEP_EN_0 (sleep_en[0])
, .SLEEP_EN_1 (sleep_en[1])
, .SLEEP_EN_2 (sleep_en[2])
, .SLEEP_EN_3 (sleep_en[3])
, .SLEEP_EN_4 (sleep_en[4])
, .SLEEP_EN_5 (sleep_en[5])
, .SLEEP_EN_6 (sleep_en[6])
, .SLEEP_EN_7 (sleep_en[7])
, .RET_EN (ret_en)
);
//--------------------------------------------------
// THIS IS ONLY FOR TESTING. REMOVE THIS LATER
// verilint 97 on - undefined instance errors turned on
//--------------------------------------------------
// ---------------------------------------------
// Declare the interface wires for Output Mux logic
// verilint 552 off - Different bits of a net are driven in different blocks (harmless,
// but some synthesis tools generate a warning for this)
reg [64:0] ram_r0_OutputMuxDataOut;
//For bitEnd 64, only one piece RAMPDP_160X65_GL_M2_D2 in the column.
// verilint 17 off - Range (rather than full vector) in the sensitivity list
always @(dout_0_0[64:0] or muxed_Di_w0[64:0] or ram_bypass)
begin
ram_r0_OutputMuxDataOut[64:0] = (ram_bypass) ? muxed_Di_w0[64:0]: dout_0_0;
end
assign r0_OutputMuxDataOut[64:0] = ram_r0_OutputMuxDataOut[64:0];
// verilint 17 on - Range (rather than full vector) in the sensitivity list
// --------------------- Output Mbist Interface logic -------------
reg mbist_ce_r0_1p;
always @(posedge la_bist_clkw0) mbist_ce_r0_1p <= mbist_ce_r0;
wire captureDR_r0 = dft_capdr_r | ((((ore)) & !mbist_en_r & !debug_mode_sync) || ( debug_mode_sync ? (1'b1& (access_en_r_1p)) : ((mbist_en_r & (mbist_ce_r0_1p) & !1'b0))));
////MSB 64 LSB 0 and total rambit is 65 and dsize is 65
wire Data_reg_SO_r0;
// verilint 110 off - Incompatible width
// verilint 630 off - Port connected to a NULL expression
// These are used for registering Ra in case of Latch arrays as well (i.e.
// used in functional path as well)
wire [64:0]data_regq;
assign Data_reg_r0[64:0] = data_regq[64:0] ;
// verilint 110 on - Incompatible width
// verilint 630 on - Port connected to a NULL expression
assign dout = Data_reg_r0;
assign mbist_Do_r0_int_net = Data_reg_r0[65-1:0];
// Declare the SO which goes out finally
`ifndef EMU
`ifndef FPGA
`define NO_EMU_NO_FPGA
// lock-up latch for ram_access SO
LNQD1PO4 testInst_ram_access_lockup (
.Q(SO_int_net),
.D(Data_reg_SO_r0),
.EN(la_bist_clkw0));
`endif
`endif
`ifndef NO_EMU_NO_FPGA
// no latch allow during emulation synthesis
assign SO_int_net = Data_reg_SO_r0;
`endif
// Ram access scan chain
wire gated_clk_jtag_Wa_reg_w0;
CKLNQD12PO4 UJ_clk_jtag_Wa_reg_w0 (.Q(gated_clk_jtag_Wa_reg_w0), .CP(clk), .E(debug_mode_sync ? (( 1'b0 | shiftDR ) ) : (1'b0 | 1'b0 | mbist_en_r | ( 1'b0 | ary_atpg_ctl) ) ), .TE(scan_en));
ScanShareSel_JTAG_reg_ext_cg #(8, 0, 0) testInst_Wa_reg_w0 (
.clk(gated_clk_jtag_Wa_reg_w0), .sel(debug_mode),
.shiftDR(shiftDR),
.reset_(1'b1), .D(muxed_Wa_w0), .Q(wadr_q),
.scanin(SI), .scanout(Wa_reg_SO_w0) );
ScanShareSel_JTAG_reg_ext_cg #(1, 0, 0) testInst_we_reg_w0 (
.clk(gated_clk_jtag_Wa_reg_w0), .sel(debug_mode),
.shiftDR(shiftDR),
.reset_(1'b1), .D(muxed_we_w0), .Q(we_q),
.scanin(Wa_reg_SO_w0), .scanout(we_reg_SO_w0) );
ScanShareSel_JTAG_reg_ext_cg #(8, 0, 0) testInst_Ra_reg_r0 (
.clk(gated_clk_jtag_Wa_reg_w0), .sel(debug_mode),
.shiftDR(shiftDR),
.reset_(1'b1), .D(muxed_Ra_r0), .Q(radr_q),
.scanin(we_reg_SO_w0), .scanout(Ra_reg_SO_r0) );
ScanShareSel_JTAG_reg_ext_cg #(1, 0, 0) testInst_re_reg_r0 (
.clk(gated_clk_jtag_Wa_reg_w0), .sel(debug_mode),
.shiftDR(shiftDR),
.reset_(1'b1), .D(muxed_re_r0), .Q(re_q),
.scanin(Ra_reg_SO_r0), .scanout(re_reg_SO_r0) );
wire gated_clk_jtag_Data_reg_r0;
CKLNQD12PO4 UJ_clk_jtag_Data_reg_r0 (.Q(gated_clk_jtag_Data_reg_r0), .CP(clk), .E(captureDR_r0 | (debug_mode_sync & shiftDR)), .TE(scan_en));
ScanShareSel_JTAG_reg_ext_cg #(65, 0, 0) testInst_Data_reg_r0 (
.clk(gated_clk_jtag_Data_reg_r0), .sel(debug_mode),
.shiftDR(shiftDR),
.reset_(1'b1), .D(r0_OutputMuxDataOut[64:0]), .Q(data_regq[64:0]),
.scanin(re_reg_SO_r0), .scanout(Data_reg_SO_r0) );
`ifdef ASSERT_ON
`ifndef SYNTHESIS
reg sim_reset_;
initial sim_reset_ = 0;
always @(posedge clk) sim_reset_ <= 1'b1;
wire start_of_sim = sim_reset_;
wire disable_clk_x_test = $test$plusargs ("disable_clk_x_test") ? 1'b1 : 1'b0;
nv_assert_no_x #(1,1,0," Try Reading Ram when clock is x for read port r0") _clk_x_test_read (clk, sim_reset_, ((disable_clk_x_test===1'b0) && (|re===1'b1 )), clk);
nv_assert_no_x #(1,1,0," Try Writing Ram when clock is x for write port w0") _clk_x_test_write (clk, sim_reset_, ((disable_clk_x_test===1'b0) && (|we===1'b1)), clk);
reg [160-1:0] written;
always@(posedge clk or negedge sim_reset_) begin
if(!sim_reset_) begin
written <= {160{1'b0}};
end else if( |we)begin
written[wa] <= 1'b1;
end
end
`endif // SYNTHESIS
`endif // ASSERT_ON
`ifdef ASSERT_ON
`ifndef SYNTHESIS
`endif
`endif
`ifdef ASSERT_ON
`ifndef SYNTHESIS
wire pwrbus_assertion_not_x_while_active = $test$plusargs ("pwrbus_assertion_not_x_while_active");
nv_assert_never #(0, 0, "Power bus cannot be X when read/write enable is set") _pwrbus_assertion_not_x_while_active_we ( we, sim_reset_ && !pwrbus_assertion_not_x_while_active, ^pwrbus_ram_pd === 1'bx);
nv_assert_never #(0, 0, "Power bus cannot be X when read/write enable is set") _pwrbus_assertion_not_x_while_active_re ( re, sim_reset_ && !pwrbus_assertion_not_x_while_active, ^pwrbus_ram_pd === 1'bx);
`endif
`endif
// submodule done
endmodule