// ================================================================
// NVDLA Open Source Project
//
// Copyright(c) 2016 - 2017 NVIDIA Corporation. Licensed under the
// NVDLA Open Hardware License; Check "LICENSE" which comes with
// this distribution for more information.
// ================================================================
// File Name: NV_NVDLA_SDP_RDMA_EG_ro.v
// ================================================================
// NVDLA Open Source Project
// 
// Copyright(c) 2016 - 2017 NVIDIA Corporation.  Licensed under the
// NVDLA Open Hardware License; Check "LICENSE" which comes with 
// this distribution for more information.
// ================================================================
// File Name: NV_NVDLA_SDP_define.h
`include "simulate_x_tick.vh"
module NV_NVDLA_SDP_RDMA_EG_ro (
   nvdla_core_clk //|< i
  ,nvdla_core_rstn //|< i
  ,pwrbus_ram_pd //|< i
  ,cfg_dp_8 //|< i
  ,cfg_dp_size_1byte //|< i
  ,cfg_mode_per_element //|< i
  ,reg2dp_channel //|< i
  ,reg2dp_height //|< i
  ,reg2dp_width //|< i
  ,rod0_wr_pd //|< i
  ,rod1_wr_pd //|< i
  ,rod2_wr_pd //|< i
  ,rod3_wr_pd //|< i
  ,rod_wr_mask //|< i
  ,rod_wr_vld //|< i
  ,rod_wr_rdy //|> o
  ,roc_wr_pd //|< i
  ,roc_wr_vld //|< i
  ,roc_wr_rdy //|> o
  ,layer_end //|> o
  ,sdp_rdma2dp_pd //|> o
  ,sdp_rdma2dp_valid //|> o
  ,sdp_rdma2dp_ready //|< i
  );
input nvdla_core_clk;
input nvdla_core_rstn;
input [31:0] pwrbus_ram_pd;
output sdp_rdma2dp_valid;
input sdp_rdma2dp_ready;
output [8*16:0] sdp_rdma2dp_pd;
input [8*8 -1:0] rod0_wr_pd;
input [8*8 -1:0] rod1_wr_pd;
input [8*8 -1:0] rod2_wr_pd;
input [8*8 -1:0] rod3_wr_pd;
input [3:0] rod_wr_mask;
input rod_wr_vld;
output rod_wr_rdy;
input [1:0] roc_wr_pd;
input roc_wr_vld;
output roc_wr_rdy;
input cfg_dp_8;
input cfg_dp_size_1byte;
input cfg_mode_per_element;
input [12:0] reg2dp_channel;
input [12:0] reg2dp_height;
input [12:0] reg2dp_width;
output layer_end;
wire [2:0] size_of_beat;
wire [12:0] size_of_width;
wire [13-3:0] size_of_surf;
reg [1:0] beat_cnt;
wire [2:0] beat_cnt_nxt;
reg mon_beat_cnt;
reg [12:0] count_h;
reg [12:0] count_w;
reg [13-3:0] count_c;
wire is_last_beat;
wire is_cube_end;
wire is_last_c;
wire is_last_h;
wire is_last_w;
wire is_line_end;
wire is_surf_end;
reg roc_rd_en;
wire [1:0] roc_rd_pd;
wire roc_rd_prdy;
wire roc_rd_pvld;
reg rodx_rd_en;
wire [8*8 -1:0] rod0_rd_pd;
wire rod0_rd_prdy;
wire rod0_rd_pvld;
wire rod0_wr_prdy;
wire rod0_wr_pvld;
wire [8*8 -1:0] rod1_rd_pd;
wire rod1_rd_prdy;
wire rod1_rd_pvld;
wire rod1_wr_prdy;
wire rod1_wr_pvld;
wire [8*8 -1:0] rod2_rd_pd;
wire rod2_rd_prdy;
wire rod2_rd_pvld;
wire rod2_wr_prdy;
wire rod2_wr_pvld;
wire [8*8 -1:0] rod3_rd_pd;
wire rod3_rd_prdy;
wire rod3_rd_pvld;
wire rod3_wr_prdy;
wire rod3_wr_pvld;
wire [1:0] rod_sel;
wire rod0_sel;
wire rod1_sel;
wire rod2_sel;
wire rod3_sel;
reg [8*8 -1:0] out_data_1bpe;
wire [8*16 -1:0] out_data_1bpe_ext;
reg [8*16 -1:0] out_data_2bpe;
reg out_vld_1bpe;
reg out_vld_2bpe;
wire out_accept;
wire out_rdy;
wire out_vld;
wire [8*16:0] out_pd;
//=======================================================
// DATA FIFO: WRITE SIDE
//=======================================================
assign rod_wr_rdy = ~(rod_wr_mask[0] & ~rod0_wr_prdy |rod_wr_mask[1] & ~rod1_wr_prdy | rod_wr_mask[2] & ~rod2_wr_prdy | rod_wr_mask[3] & ~rod3_wr_prdy );
assign rod0_wr_pvld = rod_wr_vld & rod_wr_mask[0] & ~(rod_wr_mask[1] & ~rod1_wr_prdy | rod_wr_mask[2] & ~rod2_wr_prdy | rod_wr_mask[3] & ~rod3_wr_prdy );
assign rod1_wr_pvld = rod_wr_vld & rod_wr_mask[1] & ~(rod_wr_mask[0] & ~rod0_wr_prdy | rod_wr_mask[2] & ~rod2_wr_prdy | rod_wr_mask[3] & ~rod3_wr_prdy );
assign rod2_wr_pvld = rod_wr_vld & rod_wr_mask[2] & ~(rod_wr_mask[0] & ~rod0_wr_prdy | rod_wr_mask[1] & ~rod1_wr_prdy | rod_wr_mask[3] & ~rod3_wr_prdy );
assign rod3_wr_pvld = rod_wr_vld & rod_wr_mask[3] & ~(rod_wr_mask[0] & ~rod0_wr_prdy | rod_wr_mask[1] & ~rod1_wr_prdy | rod_wr_mask[2] & ~rod2_wr_prdy );
NV_NVDLA_SDP_RDMA_EG_RO_dfifo u_rod0 (
   .nvdla_core_clk (nvdla_core_clk)
  ,.nvdla_core_rstn (nvdla_core_rstn)
  ,.rod_wr_prdy (rod0_wr_prdy)
  ,.rod_wr_pvld (rod0_wr_pvld)
  ,.rod_wr_pd (rod0_wr_pd[8*8 -1:0])
  ,.rod_rd_prdy (rod0_rd_prdy)
  ,.rod_rd_pvld (rod0_rd_pvld)
  ,.rod_rd_pd (rod0_rd_pd[8*8 -1:0])
  );
NV_NVDLA_SDP_RDMA_EG_RO_dfifo u_rod1 (
   .nvdla_core_clk (nvdla_core_clk)
  ,.nvdla_core_rstn (nvdla_core_rstn)
  ,.rod_wr_prdy (rod1_wr_prdy)
  ,.rod_wr_pvld (rod1_wr_pvld)
  ,.rod_wr_pd (rod1_wr_pd[8*8 -1:0])
  ,.rod_rd_prdy (rod1_rd_prdy)
  ,.rod_rd_pvld (rod1_rd_pvld)
  ,.rod_rd_pd (rod1_rd_pd[8*8 -1:0])
  );
NV_NVDLA_SDP_RDMA_EG_RO_dfifo u_rod2 (
   .nvdla_core_clk (nvdla_core_clk)
  ,.nvdla_core_rstn (nvdla_core_rstn)
  ,.rod_wr_prdy (rod2_wr_prdy)
  ,.rod_wr_pvld (rod2_wr_pvld)
  ,.rod_wr_pd (rod2_wr_pd[8*8 -1:0])
  ,.rod_rd_prdy (rod2_rd_prdy)
  ,.rod_rd_pvld (rod2_rd_pvld)
  ,.rod_rd_pd (rod2_rd_pd[8*8 -1:0])
  );
NV_NVDLA_SDP_RDMA_EG_RO_dfifo u_rod3 (
   .nvdla_core_clk (nvdla_core_clk)
  ,.nvdla_core_rstn (nvdla_core_rstn)
  ,.rod_wr_prdy (rod3_wr_prdy)
  ,.rod_wr_pvld (rod3_wr_pvld)
  ,.rod_wr_pd (rod3_wr_pd[8*8 -1:0])
  ,.rod_rd_prdy (rod3_rd_prdy)
  ,.rod_rd_pvld (rod3_rd_pvld)
  ,.rod_rd_pd (rod3_rd_pd[8*8 -1:0])
  );
//=======================================================
// DATA FIFO: READ SIDE
//=======================================================
always @(
  cfg_mode_per_element
  or is_last_h
  or is_last_w
  ) begin
   begin
       if (cfg_mode_per_element) begin
           rodx_rd_en = 1'b1;
       end else begin
           rodx_rd_en = is_last_h & is_last_w;
       end
   end
end
assign rod0_rd_prdy = out_rdy & rodx_rd_en & rod0_sel & ~(rod1_sel & ~rod1_rd_pvld);
assign rod1_rd_prdy = out_rdy & rodx_rd_en & rod1_sel & ~(rod0_sel & ~rod0_rd_pvld);
assign rod2_rd_prdy = out_rdy & rodx_rd_en & rod2_sel & ~(rod3_sel & ~rod3_rd_pvld);
assign rod3_rd_prdy = out_rdy & rodx_rd_en & rod3_sel & ~(rod2_sel & ~rod2_rd_pvld);
//==============
// CMD FIFO
//==============
// One entry in ROC indicates one entry from latency fifo
NV_NVDLA_SDP_RDMA_EG_RO_cfifo u_roc (
   .nvdla_core_clk (nvdla_core_clk)
  ,.nvdla_core_rstn (nvdla_core_rstn)
  ,.pwrbus_ram_pd (pwrbus_ram_pd)
  ,.roc_wr_prdy (roc_wr_rdy)
  ,.roc_wr_pvld (roc_wr_vld)
  ,.roc_wr_pd (roc_wr_pd[1:0])
  ,.roc_rd_prdy (roc_rd_prdy)
  ,.roc_rd_pvld (roc_rd_pvld)
  ,.roc_rd_pd (roc_rd_pd[1:0])
  );
always @(
  cfg_mode_per_element
  or is_surf_end
  or is_last_beat
  ) begin
    begin
        roc_rd_en = is_last_beat & (is_surf_end | cfg_mode_per_element);
    end
end
assign roc_rd_prdy = roc_rd_en & out_accept;
assign size_of_beat = roc_rd_pvld ? (roc_rd_pd[1:0] + 1) : 3'b0;
//==============
// END
//==============
assign is_line_end = is_last_w;
assign is_surf_end = is_line_end & is_last_h;
assign is_cube_end = is_surf_end & is_last_c;
//==============
// Width Count
//==============
assign size_of_width = reg2dp_width;
always @(posedge nvdla_core_clk or negedge nvdla_core_rstn) begin
  if (!nvdla_core_rstn) begin
    count_w <= {13{1'b0}};
  end else begin
    if (out_accept) begin
        begin
            if (is_line_end) begin
                count_w <= 0;
            end else begin
                count_w <= count_w + 1;
            end
        end
    end
  end
end
assign is_last_w = (count_w==size_of_width);
//==============
// HEIGHT Count
//==============
always @(posedge nvdla_core_clk or negedge nvdla_core_rstn) begin
  if (!nvdla_core_rstn) begin
    count_h <= {13{1'b0}};
  end else begin
    if (out_accept) begin
        if (is_surf_end) begin
            count_h <= 0;
        end else if (is_line_end) begin
            count_h <= count_h + 1;
        end
    end
  end
end
assign is_last_h = (count_h==reg2dp_height);
//==============
// SURF Count
//==============
assign size_of_surf = cfg_dp_8 ? {1'b0,reg2dp_channel[12:3]} : reg2dp_channel[12:3 -1];
always @(posedge nvdla_core_clk or negedge nvdla_core_rstn) begin
  if (!nvdla_core_rstn) begin
    count_c <= {(14-3){1'b0}};
  end else begin
    if (out_accept) begin
        if (is_cube_end) begin
            count_c <= 0;
        end else if (is_surf_end) begin
            count_c <= count_c + 1;
        end
    end
  end
end
assign is_last_c = (count_c==size_of_surf);
//==============
// BEAT CNT: used to foreach 1~4 16E rod FIFOs
//==============
wire [1:0] size_of_elem = (cfg_dp_size_1byte | !cfg_dp_8) ? 2'h1 : 2'h2;
assign beat_cnt_nxt = beat_cnt + size_of_elem;
always @(posedge nvdla_core_clk or negedge nvdla_core_rstn) begin
  if (!nvdla_core_rstn) begin
      {mon_beat_cnt,beat_cnt} <= 3'h0;
  end else begin
    if (out_accept) begin
      if (cfg_mode_per_element) begin
          if (is_last_beat) begin
              {mon_beat_cnt,beat_cnt} <= 3'h0;
          end else begin
              {mon_beat_cnt,beat_cnt} <= beat_cnt_nxt;
          end
      end else if (is_surf_end) begin
          if (is_last_beat) begin
              {mon_beat_cnt,beat_cnt} <= 3'h0;
          end else begin
              {mon_beat_cnt,beat_cnt} <= beat_cnt_nxt;
          end
      end
    end
  end
end
assign is_last_beat = beat_cnt_nxt == size_of_beat;
assign rod_sel = beat_cnt;
assign rod0_sel = beat_cnt == 2'h0;
assign rod2_sel = beat_cnt == 2'h2;
assign rod1_sel = (cfg_dp_size_1byte | !cfg_dp_8)? beat_cnt == 2'h1 : beat_cnt == 2'h0;
assign rod3_sel = (cfg_dp_size_1byte | !cfg_dp_8)? beat_cnt == 2'h3 : beat_cnt == 2'h2;
////dp int8 one byte per element or int16 two bytes per elment/////////// 
always @(
  rod_sel
  or rod0_rd_pd
  or rod1_rd_pd
  or rod2_rd_pd
  or rod3_rd_pd
  ) begin
    case (rod_sel)
    2'd0: out_data_1bpe = rod0_rd_pd;
    2'd1: out_data_1bpe = rod1_rd_pd;
    2'd2: out_data_1bpe = rod2_rd_pd;
    2'd3: out_data_1bpe = rod3_rd_pd;
    default : out_data_1bpe[8*8 -1:0] = {8*8{`x_or_0}};
    endcase
end
always @(
  rod_sel
  or rod0_rd_pvld
  or rod1_rd_pvld
  or rod2_rd_pvld
  or rod3_rd_pvld
  ) begin
    case (rod_sel)
    2'd0: out_vld_1bpe = rod0_rd_pvld;
    2'd1: out_vld_1bpe = rod1_rd_pvld;
    2'd2: out_vld_1bpe = rod2_rd_pvld;
    2'd3: out_vld_1bpe = rod3_rd_pvld;
    default : out_vld_1bpe = {1{`x_or_0}};
    endcase
end
//: my $m = 8;
//: foreach my $i (0..${m}-1) {
//: print "assign out_data_1bpe_ext[16*${i}+15:16*${i}] = {{8{out_data_1bpe[8*${i}+7]}}, out_data_1bpe[8*${i}+7:8*${i}]}; \n";
//: }
//| eperl: generated_beg (DO NOT EDIT BELOW)
assign out_data_1bpe_ext[16*0+15:16*0] = {{8{out_data_1bpe[8*0+7]}}, out_data_1bpe[8*0+7:8*0]}; 
assign out_data_1bpe_ext[16*1+15:16*1] = {{8{out_data_1bpe[8*1+7]}}, out_data_1bpe[8*1+7:8*1]}; 
assign out_data_1bpe_ext[16*2+15:16*2] = {{8{out_data_1bpe[8*2+7]}}, out_data_1bpe[8*2+7:8*2]}; 
assign out_data_1bpe_ext[16*3+15:16*3] = {{8{out_data_1bpe[8*3+7]}}, out_data_1bpe[8*3+7:8*3]}; 
assign out_data_1bpe_ext[16*4+15:16*4] = {{8{out_data_1bpe[8*4+7]}}, out_data_1bpe[8*4+7:8*4]}; 
assign out_data_1bpe_ext[16*5+15:16*5] = {{8{out_data_1bpe[8*5+7]}}, out_data_1bpe[8*5+7:8*5]}; 
assign out_data_1bpe_ext[16*6+15:16*6] = {{8{out_data_1bpe[8*6+7]}}, out_data_1bpe[8*6+7:8*6]}; 
assign out_data_1bpe_ext[16*7+15:16*7] = {{8{out_data_1bpe[8*7+7]}}, out_data_1bpe[8*7+7:8*7]}; 

//| eperl: generated_end (DO NOT EDIT ABOVE)
////dp int8 two byte per element/////////// 
always @(
  rod_sel
  or rod0_rd_pd
  or rod1_rd_pd
  or rod2_rd_pd
  or rod3_rd_pd
  ) begin
    case (rod_sel)
    2'd0: out_data_2bpe = {rod1_rd_pd,rod0_rd_pd};
    2'd2: out_data_2bpe = {rod3_rd_pd,rod2_rd_pd};
    default : out_data_2bpe[8*16 -1:0] = {8*16{`x_or_0}};
    endcase
end
always @(
  rod_sel
  or rod0_rd_pvld
  or rod1_rd_pvld
  or rod2_rd_pvld
  or rod3_rd_pvld
  ) begin
    case (rod_sel)
    2'd0: out_vld_2bpe = rod1_rd_pvld & rod0_rd_pvld;
    2'd2: out_vld_2bpe = rod3_rd_pvld & rod2_rd_pvld;
    default : out_vld_2bpe = {1{`x_or_0}};
    endcase
end
////mux out data ////
assign out_vld = (cfg_dp_size_1byte | !cfg_dp_8) ? out_vld_1bpe : out_vld_2bpe;
assign out_pd[8*16 -1:0] = !cfg_dp_8 ? {{8*8{1'b0}},out_data_1bpe[8*8 -1:0]} : cfg_dp_size_1byte ? out_data_1bpe_ext[8*16 -1:0] : out_data_2bpe[8*16 -1:0];
assign out_pd[8*16] = is_cube_end;
assign out_accept = out_vld & out_rdy;
NV_NVDLA_SDP_RDMA_EG_RO_pipe_p1 pipe_p1 (
   .nvdla_core_clk (nvdla_core_clk) //|< i
  ,.nvdla_core_rstn (nvdla_core_rstn) //|< i
  ,.out_pd (out_pd[8*16:0]) //|< w
  ,.out_vld (out_vld) //|< r
  ,.out_rdy (out_rdy) //|> w
  ,.sdp_rdma2dp_ready (sdp_rdma2dp_ready) //|< i
  ,.sdp_rdma2dp_pd (sdp_rdma2dp_pd[8*16:0]) //|> o
  ,.sdp_rdma2dp_valid (sdp_rdma2dp_valid) //|> o
  );
assign layer_end = sdp_rdma2dp_valid & sdp_rdma2dp_ready & sdp_rdma2dp_pd[8*16];
endmodule // NV_NVDLA_SDP_RDMA_EG_ro
// **************************************************************************************************************
// Generated by ::pipe -m -bc sdp_rdma2dp_pd (sdp_rdma2dp_valid,sdp_rdma2dp_ready) <= out_pd[8*8:0] (out_vld, out_rdy)
// **************************************************************************************************************
module NV_NVDLA_SDP_RDMA_EG_RO_pipe_p1 (
   nvdla_core_clk
  ,nvdla_core_rstn
  ,out_pd
  ,out_vld
  ,out_rdy
  ,sdp_rdma2dp_ready
  ,sdp_rdma2dp_pd
  ,sdp_rdma2dp_valid
  );
input nvdla_core_clk;
input nvdla_core_rstn;
input out_vld;
output out_rdy;
input [8*16:0] out_pd;
output [8*16:0] sdp_rdma2dp_pd;
output sdp_rdma2dp_valid;
input sdp_rdma2dp_ready;
//: my $dw = 1 + 8*16;
//: &eperl::pipe("-is -wid $dw -do sdp_rdma2dp_pd -vo sdp_rdma2dp_valid -ri sdp_rdma2dp_ready -di out_pd -vi out_vld -ro out_rdy");
//| eperl: generated_beg (DO NOT EDIT BELOW)
// Reg
reg out_rdy;
reg skid_flop_out_rdy;
reg skid_flop_out_vld;
reg [129-1:0] skid_flop_out_pd;
reg pipe_skid_out_vld;
reg [129-1:0] pipe_skid_out_pd;
// Wire
wire skid_out_vld;
wire [129-1:0] skid_out_pd;
wire skid_out_rdy;
wire pipe_skid_out_rdy;
wire sdp_rdma2dp_valid;
wire [129-1:0] sdp_rdma2dp_pd;
// Code
// SKID READY
always @(posedge nvdla_core_clk or negedge nvdla_core_rstn) begin
   if (!nvdla_core_rstn) begin
       out_rdy <= 1'b1;
       skid_flop_out_rdy <= 1'b1;
   end else begin
       out_rdy <= skid_out_rdy;
       skid_flop_out_rdy <= skid_out_rdy;
   end
end

// SKID VALID
always @(posedge nvdla_core_clk or negedge nvdla_core_rstn) begin
    if (!nvdla_core_rstn) begin
        skid_flop_out_vld <= 1'b0;
    end else begin
        if (skid_flop_out_rdy) begin
            skid_flop_out_vld <= out_vld;
        end
   end
end
assign skid_out_vld = (skid_flop_out_rdy) ? out_vld : skid_flop_out_vld;

// SKID DATA
always @(posedge nvdla_core_clk) begin
    if (skid_flop_out_rdy & out_vld) begin
        skid_flop_out_pd[129-1:0] <= out_pd[129-1:0];
    end
end
assign skid_out_pd[129-1:0] = (skid_flop_out_rdy) ? out_pd[129-1:0] : skid_flop_out_pd[129-1:0];


// PIPE READY
assign skid_out_rdy = pipe_skid_out_rdy || !pipe_skid_out_vld;

// PIPE VALID
always @(posedge nvdla_core_clk or negedge nvdla_core_rstn) begin
    if (!nvdla_core_rstn) begin
        pipe_skid_out_vld <= 1'b0;
    end else begin
        if (skid_out_rdy) begin
            pipe_skid_out_vld <= skid_out_vld;
        end
    end
end

// PIPE DATA
always @(posedge nvdla_core_clk) begin
    if (skid_out_rdy && skid_out_vld) begin
        pipe_skid_out_pd[129-1:0] <= skid_out_pd[129-1:0];
    end
end


// PIPE OUTPUT
assign pipe_skid_out_rdy = sdp_rdma2dp_ready;
assign sdp_rdma2dp_valid = pipe_skid_out_vld;
assign sdp_rdma2dp_pd = pipe_skid_out_pd;

//| eperl: generated_end (DO NOT EDIT ABOVE)
endmodule // NV_NVDLA_SDP_RDMA_EG_RO_pipe_p1
module NV_NVDLA_SDP_RDMA_EG_RO_dfifo (
      nvdla_core_clk
    , nvdla_core_rstn
    , rod_wr_prdy
    , rod_wr_pvld
    , rod_wr_pd
    , rod_rd_prdy
    , rod_rd_pvld
    , rod_rd_pd
    );
input nvdla_core_clk;
input nvdla_core_rstn;
output rod_wr_prdy;
input rod_wr_pvld;
input [8*8 -1:0] rod_wr_pd;
input rod_rd_prdy;
output rod_rd_pvld;
output [8*8 -1:0] rod_rd_pd;
//: my $dw = 8*8;
//: &eperl::pipe("-is -wid $dw -do rod_rd_pd -vo rod_rd_pvld -ri rod_rd_prdy -di rod_wr_pd -vi rod_wr_pvld -ro rod_wr_prdy");
//| eperl: generated_beg (DO NOT EDIT BELOW)
// Reg
reg rod_wr_prdy;
reg skid_flop_rod_wr_prdy;
reg skid_flop_rod_wr_pvld;
reg [64-1:0] skid_flop_rod_wr_pd;
reg pipe_skid_rod_wr_pvld;
reg [64-1:0] pipe_skid_rod_wr_pd;
// Wire
wire skid_rod_wr_pvld;
wire [64-1:0] skid_rod_wr_pd;
wire skid_rod_wr_prdy;
wire pipe_skid_rod_wr_prdy;
wire rod_rd_pvld;
wire [64-1:0] rod_rd_pd;
// Code
// SKID READY
always @(posedge nvdla_core_clk or negedge nvdla_core_rstn) begin
   if (!nvdla_core_rstn) begin
       rod_wr_prdy <= 1'b1;
       skid_flop_rod_wr_prdy <= 1'b1;
   end else begin
       rod_wr_prdy <= skid_rod_wr_prdy;
       skid_flop_rod_wr_prdy <= skid_rod_wr_prdy;
   end
end

// SKID VALID
always @(posedge nvdla_core_clk or negedge nvdla_core_rstn) begin
    if (!nvdla_core_rstn) begin
        skid_flop_rod_wr_pvld <= 1'b0;
    end else begin
        if (skid_flop_rod_wr_prdy) begin
            skid_flop_rod_wr_pvld <= rod_wr_pvld;
        end
   end
end
assign skid_rod_wr_pvld = (skid_flop_rod_wr_prdy) ? rod_wr_pvld : skid_flop_rod_wr_pvld;

// SKID DATA
always @(posedge nvdla_core_clk) begin
    if (skid_flop_rod_wr_prdy & rod_wr_pvld) begin
        skid_flop_rod_wr_pd[64-1:0] <= rod_wr_pd[64-1:0];
    end
end
assign skid_rod_wr_pd[64-1:0] = (skid_flop_rod_wr_prdy) ? rod_wr_pd[64-1:0] : skid_flop_rod_wr_pd[64-1:0];


// PIPE READY
assign skid_rod_wr_prdy = pipe_skid_rod_wr_prdy || !pipe_skid_rod_wr_pvld;

// PIPE VALID
always @(posedge nvdla_core_clk or negedge nvdla_core_rstn) begin
    if (!nvdla_core_rstn) begin
        pipe_skid_rod_wr_pvld <= 1'b0;
    end else begin
        if (skid_rod_wr_prdy) begin
            pipe_skid_rod_wr_pvld <= skid_rod_wr_pvld;
        end
    end
end

// PIPE DATA
always @(posedge nvdla_core_clk) begin
    if (skid_rod_wr_prdy && skid_rod_wr_pvld) begin
        pipe_skid_rod_wr_pd[64-1:0] <= skid_rod_wr_pd[64-1:0];
    end
end


// PIPE OUTPUT
assign pipe_skid_rod_wr_prdy = rod_rd_prdy;
assign rod_rd_pvld = pipe_skid_rod_wr_pvld;
assign rod_rd_pd = pipe_skid_rod_wr_pd;

//| eperl: generated_end (DO NOT EDIT ABOVE)
endmodule
`define FORCE_CONTENTION_ASSERTION_RESET_ACTIVE 1'b1
`include "simulate_x_tick.vh"
module NV_NVDLA_SDP_RDMA_EG_RO_cfifo (
      nvdla_core_clk
    , nvdla_core_rstn
    , roc_wr_prdy
    , roc_wr_pvld
    , roc_wr_pd
    , roc_rd_prdy
    , roc_rd_pvld
    , roc_rd_pd
    , pwrbus_ram_pd
    );
// spyglass disable_block W401 -- clock is not input to module
input nvdla_core_clk;
input nvdla_core_rstn;
output roc_wr_prdy;
input roc_wr_pvld;
input [1:0] roc_wr_pd;
input roc_rd_prdy;
output roc_rd_pvld;
output [1:0] roc_rd_pd;
input [31:0] pwrbus_ram_pd;
// Master Clock Gating (SLCG)
//
// We gate the clock(s) when idle or stalled.
// This allows us to turn off numerous miscellaneous flops
// that don't get gated during synthesis for one reason or another.
//
// We gate write side and read side separately.
// If the fifo is synchronous, we also gate the ram separately, but if
// -master_clk_gated_unified or -status_reg/-status_logic_reg is specified,
// then we use one clk gate for write, ram, and read.
//
wire nvdla_core_clk_mgated_enable; // assigned by code at end of this module
wire nvdla_core_clk_mgated; // used only in synchronous fifos
NV_CLK_gate_power nvdla_core_clk_mgate( .clk(nvdla_core_clk), .reset_(nvdla_core_rstn), .clk_en(nvdla_core_clk_mgated_enable), .clk_gated(nvdla_core_clk_mgated) );
//
// WRITE SIDE
//
wire wr_reserving;
reg roc_wr_busy_int; // copy for internal use
assign roc_wr_prdy = !roc_wr_busy_int;
assign wr_reserving = roc_wr_pvld && !roc_wr_busy_int; // reserving write space?
wire wr_popping; // fwd: write side sees pop?
reg [2:0] roc_wr_count; // write-side count
wire [2:0] wr_count_next_wr_popping = wr_reserving ? roc_wr_count : (roc_wr_count - 1'd1); // spyglass disable W164a W484
wire [2:0] wr_count_next_no_wr_popping = wr_reserving ? (roc_wr_count + 1'd1) : roc_wr_count; // spyglass disable W164a W484
wire [2:0] wr_count_next = wr_popping ? wr_count_next_wr_popping :
                                               wr_count_next_no_wr_popping;
wire wr_count_next_no_wr_popping_is_4 = ( wr_count_next_no_wr_popping == 3'd4 );
wire wr_count_next_is_4 = wr_popping ? 1'b0 :
                                          wr_count_next_no_wr_popping_is_4;
wire [2:0] wr_limit_muxed; // muxed with simulation/emulation overrides
wire [2:0] wr_limit_reg = wr_limit_muxed;
// VCS coverage off
wire roc_wr_busy_next = wr_count_next_is_4 || // busy next cycle?
                          (wr_limit_reg != 3'd0 && // check roc_wr_limit if != 0
                           wr_count_next >= wr_limit_reg) ;
// VCS coverage on
always @( posedge nvdla_core_clk_mgated or negedge nvdla_core_rstn ) begin
    if ( !nvdla_core_rstn ) begin
        roc_wr_busy_int <= 1'b0;
        roc_wr_count <= 3'd0;
    end else begin
 roc_wr_busy_int <= roc_wr_busy_next;
 if ( wr_reserving ^ wr_popping ) begin
     roc_wr_count <= wr_count_next;
        end
//synopsys translate_off
            else if ( !(wr_reserving ^ wr_popping) ) begin
        end else begin
            roc_wr_count <= {3{`x_or_0}};
        end
//synopsys translate_on
    end
end
wire wr_pushing = wr_reserving; // data pushed same cycle as roc_wr_pvld
//
// RAM
//
reg [1:0] roc_wr_adr; // current write address
// spyglass disable_block W484
always @( posedge nvdla_core_clk_mgated or negedge nvdla_core_rstn ) begin
    if ( !nvdla_core_rstn ) begin
        roc_wr_adr <= 2'd0;
    end else begin
        if ( wr_pushing ) begin
     roc_wr_adr <= roc_wr_adr + 1'd1;
        end
    end
end
// spyglass enable_block W484
wire rd_popping;
reg [1:0] roc_rd_adr; // read address this cycle
wire ram_we = wr_pushing && (roc_wr_count > 3'd0 || !rd_popping); // note: write occurs next cycle
wire [1:0] roc_rd_pd_p; // read data out of ram
wire [31 : 0] pwrbus_ram_pd;
// Adding parameter for fifogen to disable wr/rd contention assertion in ramgen.
// Fifogen handles this by ignoring the data on the ram data out for that cycle.
NV_NVDLA_SDP_RDMA_EG_RO_cfifo_flopram_rwsa_4x2 ram (
      .clk( nvdla_core_clk_mgated )
    , .pwrbus_ram_pd ( pwrbus_ram_pd )
    , .di ( roc_wr_pd )
    , .we ( ram_we )
    , .wa ( roc_wr_adr )
    , .ra ( (roc_wr_count == 0) ? 3'd4 : {1'b0,roc_rd_adr} )
    , .dout ( roc_rd_pd_p )
    );
wire [1:0] rd_adr_next_popping = roc_rd_adr + 1'd1; // spyglass disable W484
always @( posedge nvdla_core_clk_mgated or negedge nvdla_core_rstn ) begin
    if ( !nvdla_core_rstn ) begin
        roc_rd_adr <= 2'd0;
    end else begin
        if ( rd_popping ) begin
     roc_rd_adr <= rd_adr_next_popping;
        end
//synopsys translate_off
            else if ( !rd_popping ) begin
        end else begin
            roc_rd_adr <= {2{`x_or_0}};
        end
//synopsys translate_on
    end
end
//
// SYNCHRONOUS BOUNDARY
//
assign wr_popping = rd_popping; // let it be seen immediately
wire rd_pushing = wr_pushing; // let it be seen immediately
//
// READ SIDE
//
reg roc_rd_prdy_d; // roc_rd_prdy registered in cleanly
always @( posedge nvdla_core_clk or negedge nvdla_core_rstn ) begin
    if ( !nvdla_core_rstn ) begin
        roc_rd_prdy_d <= 1'b1;
    end else begin
        roc_rd_prdy_d <= roc_rd_prdy;
    end
end
wire roc_rd_prdy_d_o; // combinatorial rd_busy
wire roc_rd_pvld_p; // data out of fifo is valid
reg roc_rd_pvld_int_o; // internal copy of roc_rd_pvld_o
wire roc_rd_pvld_o = roc_rd_pvld_int_o;
assign rd_popping = roc_rd_pvld_p && !(roc_rd_pvld_int_o && !roc_rd_prdy_d_o);
reg [2:0] roc_rd_count_p; // read-side fifo count
// spyglass disable_block W164a W484
wire [2:0] rd_count_p_next_rd_popping = rd_pushing ? roc_rd_count_p :
                                                                (roc_rd_count_p - 1'd1);
wire [2:0] rd_count_p_next_no_rd_popping = rd_pushing ? (roc_rd_count_p + 1'd1) :
                                                                    roc_rd_count_p;
// spyglass enable_block W164a W484
wire [2:0] rd_count_p_next = rd_popping ? rd_count_p_next_rd_popping :
                                                     rd_count_p_next_no_rd_popping;
assign roc_rd_pvld_p = roc_rd_count_p != 0 || rd_pushing;
always @( posedge nvdla_core_clk_mgated or negedge nvdla_core_rstn ) begin
    if ( !nvdla_core_rstn ) begin
        roc_rd_count_p <= 3'd0;
    end else begin
        if ( rd_pushing || rd_popping ) begin
     roc_rd_count_p <= rd_count_p_next;
        end
//synopsys translate_off
            else if ( !(rd_pushing || rd_popping ) ) begin
        end else begin
            roc_rd_count_p <= {3{`x_or_0}};
        end
//synopsys translate_on
    end
end
//
// SKID for -rd_busy_reg
//
reg [1:0] roc_rd_pd_o; // output data register
wire rd_req_next_o = (roc_rd_pvld_p || (roc_rd_pvld_int_o && !roc_rd_prdy_d_o)) ;
always @( posedge nvdla_core_clk_mgated or negedge nvdla_core_rstn ) begin
    if ( !nvdla_core_rstn ) begin
        roc_rd_pvld_int_o <= 1'b0;
    end else begin
        roc_rd_pvld_int_o <= rd_req_next_o;
    end
end
always @( posedge nvdla_core_clk_mgated ) begin
    if ( (rd_popping) ) begin
        roc_rd_pd_o <= roc_rd_pd_p;
    end
//synopsys translate_off
        else if ( !((rd_popping)) ) begin
    end else begin
        roc_rd_pd_o <= {2{`x_or_0}};
    end
//synopsys translate_on
end
//
// FINAL OUTPUT
//
assign roc_rd_pd = !roc_rd_prdy_d_o ? roc_rd_pd_o : roc_rd_pd_p; // skid reg assign
reg roc_rd_pvld_d; // previous roc_rd_pvld
assign roc_rd_prdy_d_o = !(roc_rd_pvld_d && !roc_rd_prdy_d );
assign roc_rd_pvld = !roc_rd_prdy_d_o ? roc_rd_pvld_o : roc_rd_pvld_p;
always @( posedge nvdla_core_clk_mgated or negedge nvdla_core_rstn ) begin
    if ( !nvdla_core_rstn ) begin
        roc_rd_pvld_d <= 1'b0;
    end else begin
        roc_rd_pvld_d <= roc_rd_pvld;
    end
end
// Master Clock Gating (SLCG) Enables
//
// plusarg for disabling this stuff:
// synopsys translate_off
`ifndef SYNTH_LEVEL1_COMPILE
`ifndef SYNTHESIS
reg master_clk_gating_disabled; initial master_clk_gating_disabled = $test$plusargs( "fifogen_disable_master_clk_gating" ) != 0;
`endif
`endif
// synopsys translate_on
assign nvdla_core_clk_mgated_enable = ((wr_reserving || wr_pushing || wr_popping || (roc_wr_pvld && !roc_wr_busy_int) || (roc_wr_busy_int != roc_wr_busy_next)) || (rd_pushing || rd_popping || (roc_rd_pvld && roc_rd_prdy_d) || (roc_rd_pvld_int_o && roc_rd_prdy_d_o)) || (wr_pushing))
                               `ifdef FIFOGEN_MASTER_CLK_GATING_DISABLED
                               || 1'b1
                               `endif
// synopsys translate_off
          `ifndef SYNTH_LEVEL1_COMPILE
          `ifndef SYNTHESIS
                               || master_clk_gating_disabled
          `endif
          `endif
// synopsys translate_on
                               ;
// Simulation and Emulation Overrides of wr_limit(s)
//
`ifdef EMU
`ifdef EMU_FIFO_CFG
// Emulation Global Config Override
//
assign wr_limit_muxed = `EMU_FIFO_CFG.NV_NVDLA_SDP_RDMA_EG_RO_cfifo_wr_limit_override ? `EMU_FIFO_CFG.NV_NVDLA_SDP_RDMA_EG_RO_cfifo_wr_limit : 3'd0;
`else
// No Global Override for Emulation
//
assign wr_limit_muxed = 3'd0;
`endif // EMU_FIFO_CFG
`else // !EMU
`ifdef SYNTH_LEVEL1_COMPILE
// No Override for GCS Compiles
//
assign wr_limit_muxed = 3'd0;
`else
`ifdef SYNTHESIS
// No Override for RTL Synthesis
//
assign wr_limit_muxed = 3'd0;
`else
// RTL Simulation Plusarg Override
// VCS coverage off
reg wr_limit_override;
reg [2:0] wr_limit_override_value;
assign wr_limit_muxed = wr_limit_override ? wr_limit_override_value : 3'd0;
`ifdef NV_ARCHPRO
event reinit;
initial begin
    $display("fifogen reinit initial block %m");
    -> reinit;
end
`endif
`ifdef NV_ARCHPRO
always @( reinit ) begin
`else
initial begin
`endif
    wr_limit_override = 0;
    wr_limit_override_value = 0; // to keep viva happy with dangles
    if ( $test$plusargs( "NV_NVDLA_SDP_RDMA_EG_RO_cfifo_wr_limit" ) ) begin
        wr_limit_override = 1;
        $value$plusargs( "NV_NVDLA_SDP_RDMA_EG_RO_cfifo_wr_limit=%d", wr_limit_override_value);
    end
end
// VCS coverage on
`endif
`endif
`endif
//
// Histogram of fifo depth (from write side's perspective)
//
// NOTE: it will reference `SIMTOP.perfmon_enabled, so that
// has to at least be defined, though not initialized.
// tbgen testbenches have it already and various
// ways to turn it on and off.
//
`ifdef PERFMON_HISTOGRAM
// synopsys translate_off
`ifndef SYNTH_LEVEL1_COMPILE
`ifndef SYNTHESIS
perfmon_histogram perfmon (
      .clk ( nvdla_core_clk )
    , .max ( {29'd0, (wr_limit_reg == 3'd0) ? 3'd4 : wr_limit_reg} )
    , .curr ( {29'd0, roc_wr_count} )
    );
`endif
`endif
// synopsys translate_on
`endif
// spyglass disable_block W164a W164b W116 W484 W504
`ifdef SPYGLASS
`else
`ifdef FV_ASSERT_ON
`else
// synopsys translate_off
`endif
`ifdef ASSERT_ON
`ifdef SPYGLASS
wire disable_assert_plusarg = 1'b0;
`else
`ifdef FV_ASSERT_ON
wire disable_assert_plusarg = 1'b0;
`else
wire disable_assert_plusarg = $test$plusargs("DISABLE_NESS_FLOW_ASSERTIONS");
`endif
`endif
wire assert_enabled = 1'b1 && !disable_assert_plusarg;
`endif
`ifdef FV_ASSERT_ON
`else
// synopsys translate_on
`endif
`ifdef ASSERT_ON
//synopsys translate_off
`ifndef SYNTH_LEVEL1_COMPILE
`ifndef SYNTHESIS
always @(assert_enabled) begin
    if ( assert_enabled === 1'b0 ) begin
        $display("Asserts are disabled for %m");
    end
end
`endif
`endif
//synopsys translate_on
`endif
`endif
// spyglass enable_block W164a W164b W116 W484 W504
//The NV_BLKBOX_SRC0 module is only present when the FIFOGEN_MODULE_SEARCH
// define is set. This is to aid fifogen team search for fifogen fifo
// instance and module names in a given design.
`ifdef FIFOGEN_MODULE_SEARCH
NV_BLKBOX_SRC0 dummy_breadcrumb_fifogen_blkbox (.Y());
`endif
// spyglass enable_block W401 -- clock is not input to module
// synopsys dc_script_begin
// set_boundary_optimization find(design, "NV_NVDLA_SDP_RDMA_EG_RO_cfifo") true
// synopsys dc_script_end
endmodule // NV_NVDLA_SDP_RDMA_EG_RO_cfifo
//
// Flop-Based RAM
//
module NV_NVDLA_SDP_RDMA_EG_RO_cfifo_flopram_rwsa_4x2 (
      clk
    , pwrbus_ram_pd
    , di
    , we
    , wa
    , ra
    , dout
    );
input clk; // write clock
input [31 : 0] pwrbus_ram_pd;
input [1:0] di;
input we;
input [1:0] wa;
input [2:0] ra;
output [1:0] dout;
`ifndef FPGA
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_0 (.A(pwrbus_ram_pd[0]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_1 (.A(pwrbus_ram_pd[1]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_2 (.A(pwrbus_ram_pd[2]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_3 (.A(pwrbus_ram_pd[3]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_4 (.A(pwrbus_ram_pd[4]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_5 (.A(pwrbus_ram_pd[5]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_6 (.A(pwrbus_ram_pd[6]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_7 (.A(pwrbus_ram_pd[7]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_8 (.A(pwrbus_ram_pd[8]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_9 (.A(pwrbus_ram_pd[9]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_10 (.A(pwrbus_ram_pd[10]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_11 (.A(pwrbus_ram_pd[11]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_12 (.A(pwrbus_ram_pd[12]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_13 (.A(pwrbus_ram_pd[13]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_14 (.A(pwrbus_ram_pd[14]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_15 (.A(pwrbus_ram_pd[15]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_16 (.A(pwrbus_ram_pd[16]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_17 (.A(pwrbus_ram_pd[17]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_18 (.A(pwrbus_ram_pd[18]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_19 (.A(pwrbus_ram_pd[19]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_20 (.A(pwrbus_ram_pd[20]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_21 (.A(pwrbus_ram_pd[21]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_22 (.A(pwrbus_ram_pd[22]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_23 (.A(pwrbus_ram_pd[23]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_24 (.A(pwrbus_ram_pd[24]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_25 (.A(pwrbus_ram_pd[25]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_26 (.A(pwrbus_ram_pd[26]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_27 (.A(pwrbus_ram_pd[27]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_28 (.A(pwrbus_ram_pd[28]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_29 (.A(pwrbus_ram_pd[29]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_30 (.A(pwrbus_ram_pd[30]));
NV_BLKBOX_SINK UJ_BBOX2UNIT_UNUSED_pwrbus_31 (.A(pwrbus_ram_pd[31]));
`endif
`ifdef EMU
wire [1:0] dout_p;
// we use an emulation ram here to save flops on the emulation board
// so that the monstrous chip can fit :-)
//
reg [1:0] Wa0_vmw;
reg we0_vmw;
reg [1:0] Di0_vmw;
always @( posedge clk ) begin
    Wa0_vmw <= wa;
    we0_vmw <= we;
    Di0_vmw <= di;
end
vmw_NV_NVDLA_SDP_RDMA_EG_RO_cfifo_flopram_rwsa_4x2 emu_ram (
     .Wa0( Wa0_vmw )
   , .we0( we0_vmw )
   , .Di0( Di0_vmw )
   , .Ra0( ra[1:0] )
   , .Do0( dout_p )
   );
assign dout = (ra == 4) ? di : dout_p;
`else
reg [1:0] ram_ff0;
reg [1:0] ram_ff1;
reg [1:0] ram_ff2;
reg [1:0] ram_ff3;
always @( posedge clk ) begin
    if ( we && wa == 2'd0 ) begin
 ram_ff0 <= di;
    end
    if ( we && wa == 2'd1 ) begin
 ram_ff1 <= di;
    end
    if ( we && wa == 2'd2 ) begin
 ram_ff2 <= di;
    end
    if ( we && wa == 2'd3 ) begin
 ram_ff3 <= di;
    end
end
reg [1:0] dout;
always @(*) begin
    case( ra )
    3'd0: dout = ram_ff0;
    3'd1: dout = ram_ff1;
    3'd2: dout = ram_ff2;
    3'd3: dout = ram_ff3;
    3'd4: dout = di;
//VCS coverage off
    default: dout = {2{`x_or_0}};
//VCS coverage on
    endcase
end
`endif // EMU
endmodule // NV_NVDLA_SDP_RDMA_EG_RO_cfifo_flopram_rwsa_4x2
// emulation model of flopram guts
//
`ifdef EMU
module vmw_NV_NVDLA_SDP_RDMA_EG_RO_cfifo_flopram_rwsa_4x2 (
   Wa0, we0, Di0,
   Ra0, Do0
   );
input [1:0] Wa0;
input we0;
input [1:0] Di0;
input [1:0] Ra0;
output [1:0] Do0;
// Only visible during Spyglass to avoid blackboxes.
`ifdef SPYGLASS_FLOPRAM
assign Do0 = 2'd0;
wire dummy = 1'b0 | (|Wa0) | (|we0) | (|Di0) | (|Ra0);
`endif
// synopsys translate_off
`ifndef SYNTH_LEVEL1_COMPILE
`ifndef SYNTHESIS
reg [1:0] mem[3:0];
// expand mem for debug ease
`ifdef EMU_EXPAND_FLOPRAM_MEM
wire [1:0] Q0 = mem[0];
wire [1:0] Q1 = mem[1];
wire [1:0] Q2 = mem[2];
wire [1:0] Q3 = mem[3];
`endif
// asynchronous ram writes
always @(*) begin
  if ( we0 == 1'b1 ) begin
    #0.1;
    mem[Wa0] = Di0;
  end
end
assign Do0 = mem[Ra0];
`endif
`endif
// synopsys translate_on
// synopsys dc_script_begin
// synopsys dc_script_end
// g2c if { [find / -null_ok -subdesign vmw_NV_NVDLA_SDP_RDMA_EG_RO_cfifo_flopram_rwsa_4x2] != {} } { set_attr preserve 1 [find / -subdesign vmw_NV_NVDLA_SDP_RDMA_EG_RO_cfifo_flopram_rwsa_4x2] }
endmodule // vmw_NV_NVDLA_SDP_RDMA_EG_RO_cfifo_flopram_rwsa_4x2
//vmw: Memory vmw_NV_NVDLA_SDP_RDMA_EG_RO_cfifo_flopram_rwsa_4x2
//vmw: Address-size 2
//vmw: Data-size 2
//vmw: Sensitivity level 1
//vmw: Ports W R
//vmw: terminal we0 WriteEnable0
//vmw: terminal Wa0 address0
//vmw: terminal Di0[1:0] data0[1:0]
//vmw:
//vmw: terminal Ra0 address1
//vmw: terminal Do0[1:0] data1[1:0]
//vmw:
//qt: CELL vmw_NV_NVDLA_SDP_RDMA_EG_RO_cfifo_flopram_rwsa_4x2
//qt: TERMINAL we0 TYPE=WE POLARITY=H PORT=1
//qt: TERMINAL Wa0[%d] TYPE=ADDRESS DIR=W BIT=%1 PORT=1
//qt: TERMINAL Di0[%d] TYPE=DATA DIR=I BIT=%1 PORT=1
//qt:
//qt: TERMINAL Ra0[%d] TYPE=ADDRESS DIR=R BIT=%1 PORT=1
//qt: TERMINAL Do0[%d] TYPE=DATA DIR=O BIT=%1 PORT=1
//qt:
`endif // EMU