# BSD 3-Clause License
#
# Copyright 2020 Lawrence T. Clark, Vinay Vashishtha, or Arizona State
# University
#
# Redistribution and use in source and binary forms, with or without
# modification, are permitted provided that the following conditions are met:
#
# 1. Redistributions of source code must retain the above copyright notice,
# this list of conditions and the following disclaimer.
#
# 2. Redistributions in binary form must reproduce the above copyright
# notice, this list of conditions and the following disclaimer in the
# documentation and/or other materials provided with the distribution.
#
# 3. Neither the name of the copyright holder nor the names of its
# contributors may be used to endorse or promote products derived from this
# software without specific prior written permission.
#
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
# AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
# IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
# ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
# LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
# CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
# SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
# INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
# CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
# ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
# POSSIBILITY OF SUCH DAMAGE.
VERSION 5.8 ;
BUSBITCHARS "[]" ;
DIVIDERCHAR "/" ;
CLEARANCEMEASURE EUCLIDEAN ;
UNITS
DATABASE MICRONS 1000 ;
END UNITS
MANUFACTURINGGRID 0.001 ;
PROPERTYDEFINITIONS
LAYER LEF58_TYPE STRING ;
LAYER LEF58_PITCH STRING ;
LAYER LEF58_GAP STRING ;
LAYER LEF58_EOLKEEPOUT STRING ;
LAYER LEF58_SPACING STRING ;
LAYER LEF58_CORNERSPACING STRING ;
LAYER LEF58_WIDTHTABLE STRING ;
LAYER LEF58_CUTCLASS STRING ;
LAYER LEF58_SPACINGTABLE STRING ;
LAYER LEF58_ENCLOSURE STRING ;
LAYER LEF58_RIGHTWAYONGRIDONLY STRING ;
LAYER LEF58_RECTONLY STRING ;
END PROPERTYDEFINITIONS
#LAYER OVERLAP
# TYPE OVERLAP ;
#END OVERLAP
#
LAYER nwell
TYPE MASTERSLICE ;
PROPERTY LEF58_TYPE "TYPE NWELL ;" ;
END nwell
LAYER pwell
TYPE MASTERSLICE ;
PROPERTY LEF58_TYPE "TYPE PWELL ;" ;
END pwell
LAYER Gate
TYPE MASTERSLICE ;
END Gate
LAYER Active
TYPE MASTERSLICE ;
END Active
LAYER V0
TYPE CUT ;
SPACING 0.018 ;
WIDTH 0.018 ;
END V0
LAYER M1
TYPE ROUTING ;
DIRECTION VERTICAL ;
PITCH 0.036 ;
WIDTH 0.018 ;
SPACING 0.018 ;
AREA 0.002664 ; # Min Area # This should ideally be 16x not 4x as each dimension is scaled up by 4.0
# we only allow landing on pins (set in router) so area should not matter
SPACING 0.018 RANGE 0.036 1.0 ; # This rule is redundant with the SPACING rule
PROPERTY LEF58_EOLKEEPOUT "EOLKEEPOUT 0.01825 EXTENSION 0.0 0.0 0.031 ;" ; # Tip to Tip Spacing
PROPERTY LEF58_CORNERSPACING "CORNERSPACING CONVEXCORNER CORNERONLY 0.01 WIDTH 0.018 SPACING 0.018 ;" ;
OFFSET 0.0 ;
END M1
LAYER V1
TYPE CUT ;
SPACING 0.018 ; # unlike generate, this is really spacing, not center to center.
WIDTH 0.018 ;
END V1
LAYER M2
TYPE ROUTING ;
DIRECTION HORIZONTAL ;
WIDTH 0.018 ; # Min Width
SPACING 0.018 ; # Min Spacing
OFFSET -0.27 ;
# MINSIZE is set so that the minimum lenght of a segment is 36nm. At the proper rule size of
# 31nm, the lines can't be minimum space. This causes DRCs (like crazy). Same for M3
# MINSIZE 0.112 0.072 ;
# area is adjusted to match this (Nanoroute requires both AREA and MINSIZE)
AREA 0.002664 ;
MINSIZE 0.037 0.018 ;
PITCH 0.045 0.036 ;
# this enforces the correct routing tracks on M2 with wide M2 power rails
PROPERTY LEF58_PITCH "
PITCH 0.036 FIRSTLASTPITCH 0.045
;
" ;
# this checks for distance in any direction so is not correct
# 0.070 is to avoid conflicts with the adjacent lines. This should be caught by CORNERSPACING below
# SPACING 0.124 ENDOFLINE 0.1 WITHIN 0.070 ;
PROPERTY LEF58_SPACING
" SPACING 0.018 ENDOFLINE 0.025 WITHIN 0.02 ENDTOEND 0.031
PARALLELEDGE 0.025 WITHIN 0.02 ; " ;
PROPERTY LEF58_EOLKEEPOUT "
EOLKEEPOUT 0.025 EXTENSION 0.0 0.0125 0.031 CORNERONLY ;
" ;
PROPERTY LEF58_CORNERSPACING "
CORNERSPACING CONVEXCORNER WIDTH 0.0 SPACING 0.02 ;
" ; # CORNER to CORNER SPACING Rule
# Originally no width table for M2 since it is the follow rails.
# They can be 1x or 2x (2x causes DRCs on SAV V1). However, this seems to allow a double width M2
# on vias, which violates. Thus, this is added. Note that wide power follow rails will violate.
PROPERTY LEF58_WIDTHTABLE "
WIDTHTABLE 0.018 0.09 0.162 0.234 0.306 0.378 ;
" ;
PROPERTY LEF58_RIGHTWAYONGRIDONLY "
RIGHTWAYONGRIDONLY ;
" ;
PROPERTY LEF58_RECTONLY "
RECTONLY ;
" ;
END M2
LAYER V2
TYPE CUT ;
SPACING 0.018 ;
WIDTH 0.018 ;
END V2
LAYER M3
TYPE ROUTING ;
DIRECTION VERTICAL ;
PITCH 0.036 ;
OFFSET 0.0 ;
WIDTH 0.018 ; # Min Width
SPACING 0.018 ; # Min Spacing
# MINSIZE is set so that the minimum lenght of a segment is 36nm. At the proper rule size of
# 31nm, the lines can't be minimum space. This causes DRCs (like crazy). Same for M2
# MINSIZE 0.112 0.072 ;
# area is adjusted to match this (Nanoroute requires both AREA and MINSIZE)
AREA 0.002664 ;
MINSIZE 0.037 0.018 ;
PROPERTY LEF58_SPACING
" SPACING 0.018 ENDOFLINE 0.025 WITHIN 0.0125 ENDTOEND 0.031
PARALLELEDGE 0.025 WITHIN 0.02 ; " ;
PROPERTY LEF58_EOLKEEPOUT "
EOLKEEPOUT 0.025 EXTENSION 0.0 0.0125 0.031 CORNERONLY ;
" ;
PROPERTY LEF58_CORNERSPACING "
CORNERSPACING CONVEXCORNER WIDTH 0.0 SPACING 0.02
;
" ; # CORNER to CORNER SPACING Rule
# to make the special route widths integer values of the tracks, i.e., 1, 5, 9, 13... min widths
# the widths should be calculated in the APR tool, since viaGen does not seem to respect these
PROPERTY LEF58_WIDTHTABLE
" WIDTHTABLE 0.018 0.09 0.162 0.234 0.306 0.378 ; " ;
PROPERTY LEF58_RIGHTWAYONGRIDONLY "
RIGHTWAYONGRIDONLY ;
" ;
PROPERTY LEF58_RECTONLY "
RECTONLY ;
" ;
END M3
LAYER V3
TYPE CUT ;
# SPACING 0.072 ;
# WIDTH 0.072 ;
# different format to allow long vias for SAV power connections
PROPERTY LEF58_CUTCLASS "
CUTCLASS V3 WIDTH 0.018 LENGTH 0.024 CUTS 1 ;
CUTCLASS V3_0p480 WIDTH 0.018 LENGTH 0.12 CUTS 4 ;
CUTCLASS V3_0p864 WIDTH 0.018 LENGTH 0.216 CUTS 8 ;
" ;
PROPERTY LEF58_SPACINGTABLE "
SPACINGTABLE
DEFAULT 0.034
CUTCLASS V3 V3_0p480 V3_0p864
V3 - - - - - -
V3_0p480 - - - - - -
V3_0p864 - - - - - -
;
" ;
# ENCLOSURE CUTCLASS V3 END 0.02 SIDE 0.0 ;
# covered below?
# ENCLOSURE CUTCLASS V3 END 0.02 SIDE 0.0 ;
PROPERTY LEF58_ENCLOSURE "
ENCLOSURE CUTCLASS V3 BELOW EOL 0.0 0.005 0.0 ;
ENCLOSURE CUTCLASS V3 ABOVE EOL 0.02425 0.011 0.0 ;
ENCLOSURE CUTCLASS V3_0p480 END 0.0 SIDE 0.0 ;
ENCLOSURE CUTCLASS V3_0p864 END 0.0 SIDE 0.0 ;
" ;
END V3
LAYER M4
TYPE ROUTING ;
DIRECTION HORIZONTAL ;
PITCH 0.048 ;
WIDTH 0.024 ;
SPACING 0.024 ;
OFFSET 0.003 ;
AREA 0.008 ;
PROPERTY LEF58_SPACING "
SPACING 0.024 ENDOFLINE 0.025 WITHIN 0.04 ENDTOEND 0.04 ; " ;
PROPERTY LEF58_WIDTHTABLE
" WIDTHTABLE 0.024 0.12 0.216 0.312 0.408 ; " ;
PROPERTY LEF58_CORNERSPACING "
CORNERSPACING CONVEXCORNER CORNERONLY 0.048
WIDTH 0.0 SPACING 0.04 ;
" ;
PROPERTY LEF58_EOLKEEPOUT "
EOLKEEPOUT 0.025 EXTENSION 0.048 0.02425 0.048 CORNERONLY ;
" ;
# spacing table is required for the rule that has wide metal requires a 72nm (288 scaled)
# spacing between wide and minimum metals
SPACINGTABLE
PARALLELRUNLENGTH 0.0
WIDTH 0.0 0.024
WIDTH 0.025 0.072 ;
PROPERTY LEF58_RIGHTWAYONGRIDONLY "
RIGHTWAYONGRIDONLY ;
" ;
PROPERTY LEF58_RECTONLY "
RECTONLY ;
" ;
END M4
LAYER V4
TYPE CUT ;
# spacing is 4 * 34 = 136
# SPACING 0.136 ;
# WIDTH 0.072 ;
# ENCLOSURE 0.044 0.0 ;
PROPERTY LEF58_CUTCLASS "
CUTCLASS Vx WIDTH 0.024 LENGTH 0.024 ;
CUTCLASS Vx_0p480 WIDTH 0.024 LENGTH 0.12 CUTS 4 ;
CUTCLASS Vx_0p864 WIDTH 0.024 LENGTH 0.216 CUTS 8 ;
CUTCLASS Vx_1p248 WIDTH 0.024 LENGTH 0.312 CUTS 12 ;
CUTCLASS Vx_1p632 WIDTH 0.024 LENGTH 0.408 CUTS 16 ;
" ;
PROPERTY LEF58_SPACINGTABLE "
SPACINGTABLE
DEFAULT 0.034
CUTCLASS Vx Vx_0p480 Vx_0p864 Vx_1p248 Vx_1p632
Vx - - - - - - - - - -
Vx_0p480 - - - - - - - - - -
Vx_0p864 - - - - - - - - - -
Vx_1p248 - - - - - - - - - -
Vx_1p632 - - - - - - - - - -
;
" ;
PROPERTY LEF58_ENCLOSURE "
ENCLOSURE CUTCLASS Vx 0.011 0.0 ;
ENCLOSURE CUTCLASS Vx EOL 0.0 0.011 0.011 ;
ENCLOSURE CUTCLASS Vx_0p480 END 0.0 SIDE 0.0 ;
ENCLOSURE CUTCLASS Vx_0p864 END 0.0 SIDE 0.0 ;
ENCLOSURE CUTCLASS Vx_1p248 END 0.0 SIDE 0.0 ;
ENCLOSURE CUTCLASS Vx_1p632 END 0.0 SIDE 0.0 ;
" ;
END V4
LAYER M5
TYPE ROUTING ;
DIRECTION VERTICAL ;
PITCH 0.048 ;
WIDTH 0.024 ;
SPACING 0.024 ;
OFFSET 0.0 ;
AREA 0.008 ;
PROPERTY LEF58_SPACING "
SPACING 0.024 ENDOFLINE 0.025 WITHIN 0.04 ENDTOEND 0.04 ; " ;
MINIMUMDENSITY 15.0 ;
MAXIMUMDENSITY 90.0 ;
DENSITYCHECKWINDOW 20.0 20.0 ;
DENSITYCHECKSTEP 10.0 ;
PROPERTY LEF58_WIDTHTABLE
" WIDTHTABLE 0.024 0.12 0.216 0.312 0.408 0.504 0.6 0.696 0.792 0.888 0.984 ; " ;
PROPERTY LEF58_CORNERSPACING "
CORNERSPACING CONVEXCORNER CORNERONLY 0.048
WIDTH 0.0 SPACING 0.04 ;
" ;
PROPERTY LEF58_EOLKEEPOUT "
EOLKEEPOUT 0.025 EXTENSION 0.048 0.02425 0.048
CORNERONLY ;
" ;
SPACINGTABLE
PARALLELRUNLENGTH 0.0
WIDTH 0.0 0.024
WIDTH 0.025 0.072 ;
PROPERTY LEF58_RIGHTWAYONGRIDONLY "
RIGHTWAYONGRIDONLY ;
" ;
PROPERTY LEF58_RECTONLY "
RECTONLY ;
" ;
END M5
LAYER V5
TYPE CUT ;
PROPERTY LEF58_CUTCLASS "
CUTCLASS Vx WIDTH 0.024 LENGTH 0.032 ;
CUTCLASS Vx_0p480 WIDTH 0.024 LENGTH 0.16 CUTS 4 ;
CUTCLASS Vx_0p864 WIDTH 0.024 LENGTH 0.288 CUTS 8 ;
CUTCLASS Vx_1p248 WIDTH 0.024 LENGTH 0.416 CUTS 12 ;
CUTCLASS Vx_1p632 WIDTH 0.024 LENGTH 0.544 CUTS 16 ;
" ;
PROPERTY LEF58_SPACINGTABLE "
SPACINGTABLE
DEFAULT 0.034
CUTCLASS Vx Vx_0p480 Vx_0p864 Vx_1p248 Vx_1p632
Vx - - - - - - - - - -
Vx_0p480 - - - - - - - - - -
Vx_0p864 - - - - - - - - - -
Vx_1p248 - - - - - - - - - -
Vx_1p632 - - - - - - - - - -
;
" ;
# end refers to the end of the VIA! Thus, since it is rectangular the proper
# enclosure is on the side not the end...
# ENCLOSURE CUTCLASS Vx END 0.0 SIDE 0.044 ; But--this refers to top and bottom
# actually passing the rule is done by having the correct vias below.
PROPERTY LEF58_ENCLOSURE "
ENCLOSURE CUTCLASS Vx EOL 0.02425 0.011 0.011 ;
ENCLOSURE CUTCLASS Vx_0p480 END 0.0 SIDE 0.0 ;
ENCLOSURE CUTCLASS Vx_0p864 END 0.0 SIDE 0.0 ;
ENCLOSURE CUTCLASS Vx_1p248 END 0.0 SIDE 0.0 ;
ENCLOSURE CUTCLASS Vx_1p632 END 0.0 SIDE 0.0 ;
" ;
# PROPERTY LEF58_ENCLOSURE "
# ENCLOSURE CUTCLASS Vx EOL 0.0 0.044 0.0 ;
# " ;
END V5
LAYER M6
TYPE ROUTING ;
DIRECTION HORIZONTAL ;
PITCH 0.064 ;
WIDTH 0.032 ;
SPACING 0.032 ;
AREA 0.00875 ; # Areas still need tweaking
PROPERTY LEF58_SPACING
" SPACING 0.032 ENDOFLINE 0.0375 WITHIN 0.04 ENDTOEND 0.04 ; " ;
PROPERTY LEF58_WIDTHTABLE
" WIDTHTABLE 0.032 0.16 0.288 0.416 0.544 ; " ;
PROPERTY LEF58_CORNERSPACING "
CORNERSPACING CONVEXCORNER CORNERONLY 0.048
WIDTH 0.0 SPACING 0.04 ;
" ;
PROPERTY LEF58_EOLKEEPOUT "
EOLKEEPOUT 0.05 EXTENSION 0.048 0.03225 0.048 CORNERONLY ;
" ;
SPACINGTABLE
PARALLELRUNLENGTH 0.0
WIDTH 0.0 0.024
WIDTH 0.025 0.072 ;
PROPERTY LEF58_RIGHTWAYONGRIDONLY "
RIGHTWAYONGRIDONLY ;
" ;
PROPERTY LEF58_RECTONLY "
RECTONLY ;
" ;
END M6
LAYER V6
TYPE CUT ;
PROPERTY LEF58_CUTCLASS "
CUTCLASS Vx WIDTH 0.032 LENGTH 0.032 ;
CUTCLASS Vx_0p640 WIDTH 0.032 LENGTH 0.16 CUTS 4 ;
CUTCLASS Vx_1p152 WIDTH 0.032 LENGTH 0.288 CUTS 8 ;
CUTCLASS Vx_1p664 WIDTH 0.032 LENGTH 0.416 CUTS 12 ;
CUTCLASS Vx_2p176 WIDTH 0.032 LENGTH 0.544 CUTS 16 ;
" ;
PROPERTY LEF58_SPACINGTABLE "
SPACINGTABLE
DEFAULT 0.034
CUTCLASS Vx Vx_0p640 Vx_1p152 Vx_1p664 Vx_2p176
Vx - - - - - - - - - -
Vx_0p640 - - - - - - - - - -
Vx_1p152 - - - - - - - - - -
Vx_1p664 - - - - - - - - - -
Vx_2p176 - - - - - - - - - -
;
" ;
PROPERTY LEF58_ENCLOSURE "
ENCLOSURE CUTCLASS Vx 0.011 0.0 ;
ENCLOSURE CUTCLASS Vx EOL 0.0 0.011 0.011 ;
ENCLOSURE CUTCLASS Vx_0p640 END 0.0 SIDE 0.0 ;
ENCLOSURE CUTCLASS Vx_1p152 END 0.0 SIDE 0.0 ;
ENCLOSURE CUTCLASS Vx_1p664 END 0.0 SIDE 0.0 ;
ENCLOSURE CUTCLASS Vx_2p176 END 0.0 SIDE 0.0 ;
" ;
END V6
LAYER M7
TYPE ROUTING ;
DIRECTION VERTICAL ;
PITCH 0.064 ;
WIDTH 0.032 ;
SPACING 0.032 ;
AREA 0.00875 ; # Areas still need tweaking
PROPERTY LEF58_SPACING
" SPACING 0.03 ENDOFLINE 0.0375 WITHIN 0.04 ENDTOEND 0.04 ; " ;
PROPERTY LEF58_WIDTHTABLE
" WIDTHTABLE 0.032 0.16 0.288 0.416 0.544 ; " ;
TYPE ROUTING ;
DIRECTION VERTICAL ;
PROPERTY LEF58_CORNERSPACING "
CORNERSPACING CONVEXCORNER CORNERONLY 0.075
WIDTH 0.0 SPACING 0.04 ;
" ;
PROPERTY LEF58_EOLKEEPOUT "
EOLKEEPOUT 0.05 EXTENSION 0.048 0.03225 0.048
CORNERONLY ;
" ;
SPACINGTABLE
PARALLELRUNLENGTH 0.0
WIDTH 0.0 0.024
WIDTH 0.025 0.072 ;
PROPERTY LEF58_RIGHTWAYONGRIDONLY "
RIGHTWAYONGRIDONLY ;
" ;
PROPERTY LEF58_RECTONLY "
RECTONLY ;
" ;
END M7
LAYER V7
TYPE CUT ;
SPACING 0.046 ;
WIDTH 0.032 ;
END V7
LAYER M8
TYPE ROUTING ;
DIRECTION HORIZONTAL ;
PITCH 0.08 0.08 ;
WIDTH 0.04 ;
AREA 7.52 ;
SPACINGTABLE
PARALLELRUNLENGTH 0.0 0.39975 1.19975 1.79975
WIDTH 0.0 0.04 0.04 0.04 0.04
WIDTH 0.05975 0.04 0.04 0.04 0.04
WIDTH 0.07975 0.04 0.04 0.04 0.04
WIDTH 0.11975 0.04 0.04 0.04 0.04
WIDTH 0.49975 0.04 0.04 0.04 0.5
WIDTH 0.99975 0.04 0.04 0.04 1.0 ;
MINIMUMCUT 2 WIDTH 1.805 WITHIN 1.705 FROMBELOW ;
MINIMUMCUT 2 WIDTH 1.805 WITHIN 1.705 FROMABOVE ;
MAXWIDTH 2.0 ;
MINSTEP 0.04 STEP ;
END M8
LAYER V8
TYPE CUT ;
SPACING 0.057 ;
WIDTH 0.04 ;
END V8
LAYER M9
TYPE ROUTING ;
DIRECTION VERTICAL ;
PITCH 0.08 0.08 ;
WIDTH 0.04 ;
AREA 7.52 ;
SPACINGTABLE
PARALLELRUNLENGTH 0.0 0.39975 1.19975 1.79975
WIDTH 0.0 0.04 0.04 0.04 0.04
WIDTH 0.05975 0.04 0.04 0.04 0.04
WIDTH 0.07975 0.04 0.04 0.04 0.04
WIDTH 0.11975 0.04 0.04 0.04 0.04
WIDTH 0.49975 0.04 0.04 0.04 0.5
WIDTH 0.99975 0.04 0.04 0.04 1.0 ;
MINIMUMCUT 2 WIDTH 1.805 WITHIN 1.705 FROMABOVE ;
MINSTEP 0.04 STEP ;
END M9
LAYER V9
TYPE CUT ;
SPACING 0.057 ;
WIDTH 0.04 ;
END V9
LAYER Pad
TYPE ROUTING ;
DIRECTION HORIZONTAL ;
PITCH 0.08 0.08 ;
WIDTH 0.04 ;
SPACINGTABLE
PARALLELRUNLENGTH 0.0 11.99975
WIDTH 0.0 2.0 2.0
WIDTH 11.99975 2.0 3.0 ;
MINIMUMCUT 1 WIDTH 0.04 WITHIN 1.705 FROMBELOW ;
MINIMUMCUT 1 WIDTH 0.36 WITHIN 1.705 FROMBELOW ;
MINIMUMCUT 2 WIDTH 1.805 WITHIN 1.705 FROMBELOW ;
MINIMUMDENSITY 20.0 ;
MAXIMUMDENSITY 80.0 ;
DENSITYCHECKWINDOW 100.0 100.0 ;
DENSITYCHECKSTEP 50.0 ;
END Pad
# vias
VIA VIA9Pad Default
LAYER M9 ;
RECT -0.05 -0.05 0.05 0.05 ;
LAYER Pad ;
RECT -0.05 -0.05 0.05 0.05 ;
LAYER V9 ;
RECT -0.05 -0.05 0.05 0.05 ;
END VIA9Pad
VIA VIA89 Default
LAYER M8 ;
RECT -0.02 -0.02 0.02 0.02 ;
LAYER M9 ;
RECT -0.02 -0.02 0.02 0.02 ;
LAYER V8 ;
RECT -0.02 -0.02 0.02 0.02 ;
END VIA89
VIA VIA78 Default
LAYER M7 ;
RECT -0.016 -0.027 0.016 0.027 ;
LAYER M8 ;
RECT -0.027 -0.020 0.027 0.020 ;
LAYER V7 ;
RECT -0.016 -0.016 0.016 0.016 ;
END VIA78
VIA VIA67 Default
LAYER M6 ;
RECT -0.027 -0.016 0.027 0.016 ;
LAYER M7 ;
RECT -0.016 -0.027 0.016 0.027 ;
LAYER V6 ;
RECT -0.016 -0.016 0.016 0.016 ;
END VIA67
VIA VIA56 Default
LAYER M5 ;
RECT -0.012 -0.027 0.012 0.027 ;
LAYER M6 ;
RECT -0.023 -0.016 0.023 0.016 ;
LAYER V5 ;
RECT -0.012 -0.016 0.012 0.016 ;
END VIA56
VIA VIA45 Default
LAYER M4 ;
RECT -0.023 -0.012 0.023 0.012 ;
LAYER M5 ;
RECT -0.012 -0.023 0.012 0.023 ;
LAYER V4 ;
RECT -0.012 -0.012 0.012 0.012 ;
END VIA45
VIA VIA34 Default
LAYER M3 ;
RECT -0.009 -0.017 0.009 0.017 ;
LAYER M4 ;
RECT -0.02 -0.012 0.02 0.012 ;
LAYER V3 ;
RECT -0.009 -0.012 0.009 0.012 ;
END VIA34
VIA VIA23 Default
LAYER M2 ;
RECT -0.014 -0.009 0.014 0.009 ;
LAYER M3 ;
RECT -0.009 -0.014 0.009 0.014 ;
LAYER V2 ;
RECT -0.009 -0.009 0.009 0.009 ;
END VIA23
VIA VIA12 Default
LAYER M1 ;
RECT -0.009 -0.011 0.009 0.011 ;
LAYER M2 ;
RECT -0.014 -0.009 0.014 0.009 ;
LAYER V1 ;
RECT -0.009 -0.009 0.009 0.009 ;
END VIA12
#################################
### VIARULE GENERATE DEFAULTS ###
#################################
VIARULE Pad_M9 GENERATE DEFAULT
LAYER M9 ;
ENCLOSURE 0.0 0.0 ;
LAYER Pad ;
ENCLOSURE 0.011 0.0 ;
LAYER V9 ;
RECT -0.016 -0.016 0.016 0.016 ;
SPACING 0.078 BY 0.078 ;
END Pad_M9
VIARULE M9_M8 GENERATE DEFAULT
LAYER M8 ;
ENCLOSURE 0.0 0.0 ;
LAYER M9 ;
ENCLOSURE 0.0 0.02 ;
LAYER V8 ;
RECT -0.02 -0.02 0.02 0.02 ;
SPACING 0.097 BY 0.097 ;
END M9_M8
VIARULE M8_M7 GENERATE DEFAULT
LAYER M7 ;
ENCLOSURE 0.0 0.0 ;
LAYER M8 ;
ENCLOSURE 0.011 0.0 ;
LAYER V7 ;
RECT -0.016 -0.016 0.016 0.016 ;
SPACING 0.078 BY 0.078 ;
END M8_M7
VIARULE M7_M6 GENERATE DEFAULT
LAYER M6 ;
ENCLOSURE 0.011 0.0 ;
LAYER M7 ;
ENCLOSURE 0.0 0.011 ;
LAYER V6 ;
RECT -0.016 -0.016 0.016 0.016 ;
SPACING 0.078 BY 0.078 ;
END M7_M6
VIARULE M6_M5 GENERATE DEFAULT
LAYER M5 ;
ENCLOSURE 0.011 0.0 ;
WIDTH 0.024 TO 0.024 ;
LAYER M6 ;
ENCLOSURE 0.011 0.0 ;
WIDTH 0.032 TO 0.032 ;
LAYER V5 ;
RECT -0.012 -0.016 0.012 0.016 ;
SPACING 0.058 BY 0.308 ; # purposely crazy to avoid dual cut on routing
END M6_M5
# to make the wide vias for power stripes (still SAV)
VIARULE M3_M2widePWR0p936 GENERATE
LAYER M2 ;
ENCLOSURE 0.0 0.0 ;
LAYER M3 ;
ENCLOSURE 0.0 0.0 ;
WIDTH 0.234 TO 0.234 ;
LAYER V2 ;
RECT -0.117 -0.009 0.117 0.009 ;
SPACING 0.277 BY 0.036 ;
END M3_M2widePWR0p936
# to make the wide vias for powers (still SAV)
VIARULE M4_M3widePWR0p864 GENERATE
LAYER M3 ;
ENCLOSURE 0.0 0.0 ;
WIDTH 0.2335 TO 0.2345 ;
LAYER M4 ;
ENCLOSURE 0.0 0.0 ;
WIDTH 0.2155 TO 0.2165 ;
LAYER V3 ;
RECT -0.009 -0.108 0.009 0.108 ;
SPACING 0.036 BY 0.277 ;
END M4_M3widePWR0p864
# to make the wide vias for powers (still SAV)
VIARULE M5_M4widePWR0p864 GENERATE
LAYER M4 ;
ENCLOSURE 0.0 0.0 ;
LAYER M5 ;
ENCLOSURE 0.0 0.0 ;
WIDTH 0.216 TO 0.216 ;
LAYER V4 ;
RECT -0.108 -0.012 0.108 0.012 ;
SPACING 0.532 BY 0.096 ;
END M5_M4widePWR0p864
# to make the wide vias for powers (still SAV)
VIARULE M6_M5widePWR1p152 GENERATE
LAYER M5 ;
ENCLOSURE 0.0 0.0 ;
LAYER M6 ;
ENCLOSURE 0.0 0.0 ;
WIDTH 0.288 TO 0.288 ;
LAYER V5 ;
RECT -0.012 -0.144 0.012 0.144 ;
SPACING 0.096 BY 0.382 ;
END M6_M5widePWR1p152
# to make the wide vias for powers (still SAV)
VIARULE M7_M6widePWR1p152 GENERATE
LAYER M6 ;
ENCLOSURE 0.0 0.0 ;
LAYER M7 ;
ENCLOSURE 0.0 0.0 ;
WIDTH 0.288 TO 0.288 ;
LAYER V6 ;
RECT -0.144 -0.016 0.144 0.016 ;
SPACING 0.532 BY 0.096 ;
END M7_M6widePWR1p152
VIARULE M2_M1 GENERATE DEFAULT
LAYER M1 ;
ENCLOSURE 0.0 0.0 ;
LAYER M2 ;
ENCLOSURE 0.002 0.0 ;
LAYER V1 ;
RECT -0.009 -0.009 0.009 0.009 ;
SPACING 0.036 BY 0.036 ;
END M2_M1
END LIBRARY